Vag Mileage Correction Equipment Remote Control Digimaster 18
Mileage Correction
DigiMaster 18 is a programming machine with multifunction which can
connect computer through the USB access. Apart from the ordinary
functions, there are special models function.
Mileage Correction tool Digimaster 18
Feature Function:
Remote Control: Wherever you are,there is our serving, Digimaster 18 can help you
to solve your problem by "ELINK".
Intellectualized: Guiding operate, you will feel easy to adjust odometer.
Data analyze: it can help you to solve the problem of the new car by yourself
soon.
Pin test: make sure the chip well contact in the socker. Protect your chip
and data.
1. Maintenance of the odometer: It is for correcting the mileage of
the odometer (identify the data stored in the chip and analyze the
data rule of them automatically).
Repair the problem of the odometer & Coding the new odometer .
2. Universal Programmer: used when program and modify on the EEPROM
with no more than 16 architraves.
3. Decoding Audio: this function module is designed for all kinds
of audio with digital code. You can decode the original code when
the original code is missed.
4. Restore the airbag: this function module is designed for
restoring the data of the airbag after the traffic accident.
5. Computer decoding: used to read the immobilizer of VW/ Audi.
6. Signal generator: used to generate signal in different frequency
of all kinds of sensors ( photoelectricity sensor;
magnetoelectricity sensor, hall sensor etc. ), simulation test for
the odograph and ECU.
Fool-proof operation
With graphical and induced operation user display, you can learn it
even without the help of the manipulation manual. Just like
WINDOWS, it supplies a lot of tips and on-line service. It can find
out corresponding type automatically if only enter the type of
manufacturer, so it is no need to waste any time in the list of
products.
Omnipotent drive for the architrave
Every architrave is not only can supple with VCC, VPP or GND but
also TTL high/low voltage, high-speed timepiece and three
conditions. Thus, it can program on all DIP devices with no more
than 16 architraves without adapter. So, it’s not only can program
on those DIP devices which exist in market at present but also can
meet the need of the new device with no more than 16 architraves in
the future.
The check function of inserting and contacting
DigiMaster 18 carry an inserting and contacting inspection on every
parts of an apparatus which can prevent you from programming under
the bad-contact and wrong position thus damage can be prevented.
Specifications:
1. System Requirements
Memory: A minimum of 128 Mega free RAM.
Mass Storage: At least one CD drives and hard disk drives.
Display Adapter: At least one of VGA Adapter.
Monitor: Any monitor compatible with the above display adapter.
Operation System: WINDOWS 98/ME/2000/XP/2003
Standard USB port
2. Install hardware
Connecting the DigiMaster 18 and USB port then turn on the power of
DigiMaster 18.
Then install the USB drives before you use it.
Odometer Correction:
Include:BMW 7 Series E65/E66/E60/E90 (from 2001 to 4th of 2005),no
need to replace M35080 (memory)Mercedes Benz W203/W220/W211 cluster
and (EZS)(2000-2005) ignition module
adjustingHyundai/Peugeot/Renault/Honda/Picasso (NEC CPU) cluster
adjustingVolvo XC90,S80
Notice:
1. When use the module of signal generator, need to install signal
output adapter and use appropriative signal output equipment.
2. Please pay attention to distinguish 5V and 12V output voltages
and the type of signal. DC signal apply to analog photoelectricity
and Hall sensor signal; AC signal apply to analog
magnetoelectricity sensor signal.
