Powder Coated 102mm Replacement Conveyor Rollers For Mining
Industry
Mining Industry Conveyor Roller Carrier Roller Steel Pipe Guide
Roller Factory
The roller is an important part of the belt conveyor. There are
many types and large quantities. The function is to support the
belt, reduce the running resistance of the belt, and make the
verticality of the belt not exceed a certain limit to ensure the
smooth running of the belt.
idlers are classified into self-aligning idlers, buffer idlers,
trough idlers, and parallel idlers according to their uses. The
function of the self-aligning roller is to correct the deviation of
the belt conveyor. Usually, a rotary groove-shaped self-aligning
roller is installed on the heavy-duty section of the conveyor, and
a parallel self-aligning roller is installed on the no-load
section. The buffer roller is applied to the tailstock of the
machine according to the actual situation. When receiving the
material, it can reduce the impact of the material on the belt,
which is beneficial to the service life of the long belt. The
trough-shaped roller is generally composed of two side rollers and
a flat roller. The groove angle is generally 30 degrees. For a
detachable belt conveyor, the three rollers of the trough-shaped
roller are hinged to each other, so Called hinged roller. The
parallel roller is generally a long roller, which is installed at
the lower end under pressure, so it is called the lower roller.
The conveyor idler roller specification:
1. Roller Diameter: 63.5-214mm
2. Roller Length: 160mm to 3020mm
3. Roller tube: Q235 seamless carbon steel
4. Color: According to custom requirements
5. Painting: ordinary painting, hot galvanized painting, electric
static spraying painting, baked painting
6. Welding: CO2 gas shielded arc welding end
7. Professional roller production line
8. Professional designing and inspection team
9. Certification: ISO9001; 2008 ISO14001; 2004 ISO 18001
conveyor roller Description
Specification |
| Diameter | 60-219mm |
| Length | 100-3500mm |
| Tube | Q235(GB),Rubber,Nylon,HDPE |
| Shaft | 45# steel(GB) equal to C45 |
| Bearing | Single & Double Row Deep Groove Ball Bearing 2RZ&2Z wigh C3
clearance |
| Grease | Lithium soap type grease,grease retaining inner seal with
Multi-stage Labyrinth and Retention Cap with Outboard Rubbing
Flinger Seal |
| Lubrication | Grease is Lithium soap type grease with Rust Inhibitors |
| Welding | Mixed gas shielded arc welding end |
| Painting | Ordinary painting, hot galvanized painting, electric static
spraying painting, baked painting |
| Standard Diameter(mm) | Standard Diameter(Inch) | Lengthscope (mm) | Bearings Type (Min-Max) | dler's shell wall thinkness |
| 63.5 | 21/2 | 150-3500 | 204 | 3.0mm-3.75mm |
| 76 | 3 | 150-3500 | 204 205 | 3.0mm-4.0mm |
| 89 | 31/3 | 150-3500 | 204 205 | 3.0mm-4.0mm |
| 102 | 4 | 150-3500 | 204 205 305 | 3.5mm-4.0mm |
| 108 | 41/4 | 150-3500 | 204 205 305 306 | 3.5mm-4.0mm |
| 114 | 41/2 | 150-3500 | 204 205 305 306 | 3.5mm-4.5mm |
| 127 | 5 | 150-3500 | 204 205 305 306 | 3.5mm-4.5mm |
| 133 | 51/4 | 150-3500 | 204 206 207 305 306 | 3.5mm-4.5mm |
| 152 | 6 | 150-3500 | 204 206 207 305 306 307 308 | 4.0mm-4.5mm |
| 159 | 61/4 | 150-3500 | 204 206 207 305 306 307 308 | 4.0mm-4.5mm |
| 165 | 61/2 | 150-3500 | 207 305 306 307 308 | 4.5mm-6.0mm |
| 194 | 75/8 | 150-3500 | 207 307 308 309 310 | 4.5mm-6.0mm |
| 219 | 85/8 | 150-3500 | 308 309 310 | 4.5mm-6.0mm |
The roller is an important part of the conveyor. It has a large
number, large force and long pressure-bearing time. It needs to be
maintained regularly to reduce unnecessary loss and extend the
service life of the roller and its supporting conveyor.
Pay attention to the following points when maintaining the roller:
1. In the normal use of the roller, the collision to the roller
should be minimized, and it should not be disassembled and
assembled at will.
2. For the replacement of labyrinth seals, the original
factory-designated accessories should be used, and they should be
classified and loaded according to requirements. They should not be
used chaotically to avoid the failure of normal operation after
assembly of different specifications.
3. When replacing the bearing, the opening of the bearing cage
should be facing outwards, and a certain gap should be left after
the bearing is installed into the roller, so that it cannot be
crushed.
4. When resting, the idler can be removed to avoid deformation
caused by extended time of bearing pressure, which will affect the
use effect.
5. After the work is over, clean the roller with a special cleaning
agent, and place the washed roller in a cool and ventilated place,
and continue to use it after air-drying.
6. Items such as protective film can be used to wrap the rollers
that need to be temporarily stored to prevent contamination.
