FRAME PLATE And FRAME PLATE LINER INSERT Pump Spare Parts For 65QV
- SP Submerged Slurry Pump
Overview
The 65QV - SP Submerged Slurry Pump is a vertical centrifugal
slurry pump, single-stage, single-suction cantilever type knot.
Suitable for conveying abrasive, coarse particles, high
concentration slurry. The pump is typically immersed in the tank or
in the pit. It does not require any shaft seals and shaft seals to
work properly under inhaled conditions. The SP type flow element
and shaft are made of metal and are suitable for conveying abrasive
slurry. SP type submerged pump is widely used in metallurgy,
mining, coal, electric power, building materials and other
departments.
The FRAME PLATE SP65092 And FRAME PLATE LINER INSERT SP65041 Pump
Spare Parts are 65 QV-SP overcurrent parts made of high chrome wear
resistant metal. It has excellent wear characteristics and is
suitable for conveying abrasive slurries.
Material
| Type | Code | Mark | Mechanism Performance | Special Performance | Application |
| | HRC |
| δw/δb | αk |
| MPa | J/cm2 |
| Anti-wear white iron | A05 | KmTBCr27 | ≥700 | 6--10 | ≥56 | Erode resistance is a little bit lower than A07 with certain
corrosive resistance | Used for higher wear condition with PH between 5 and 12 |
| A07 | KmTBCr15Mo | ≥550 | 4--8 | ≥59 | Best erode resistance but lower wear resistance than A05 | Used for higher wear condition |
| A01 | KmTBCr8 | ≥550 | 6--8 | ≥55 | The erode resistance is about 0.9 times of A05. | Used for mud pump |
| A11 | KmTBMnMo | ≥400 | 3--6 | 38-42 | Lighter erode resistance and lower hardness. It can be perforated
and tapped. | Used for light wear condition with fine grain. |
| Anti- wear &anti-corrosive iron | A49 | -- | ≥600 | -- | 43 | It has certain erode and corrosive resistance in low PH condition.
Its wear resistance is nearly equal to A03 | For lower PH condition,especially for flue gas. For low sour
condition desulphuration installation (PH≥4) |
| A33 | -- | -- | -- | 35 | It has certain erode and corrosive resistance that is similar to
A03 and certain corrosive resistance. | It can transport oxygenated slurry with PH not be less than 1. |
| Anti-wear cast steel | A22 | -- | 1200 | -- | 45 | Fine anti-erode & anti-corrosive, high hardness. | Used for dredge pump casing. |
| A23 | -- | 700 | -- | HB500-600 | Higher hardness and anti-erode. | Used for anti-wear &corrosive and high erode condition. |
| A25 | -- | -- | -- | HB300-350 | Lower hardness, better anti-wear & anti-corrosive and weldable. | Used for light erode and wear condition. |
Pump replaced parts material:
1) Material: D21, G01, A05...
2) Shaft material: 45#, 40Cr, SS304, SS315...
3) Shaft sleeve material: 3Cr13, 4Cr13, SS304, SS316...
4) Lantern ring material: 304, 316, PTFE, Cu...
5) Bearing housing/ bearing end cover material: G01, D21...
6) Wet end part material: A05, A07, A49, A51, A33, A61, R08, R26,
R33, R38, R55, S01, S12, S21, S42,
S50, U01, EPDM, PU, CR..
Spare parts materials
| NO. | Name | code | Regular material | Alternational materials |
| 1 | Impeller | | A05(Cr27) | A49,Rubber,304,316 |
| 2 | Throatbush | 083 | A05(Cr27) | A49,Rubber,304,316 |
| 3 | Frame plate liner insert | 041 | A05(Cr27) | A49,Rubber,304,316 |
| 4 | Volute liner | 110 | A05(Cr27) | A49,Rubber,304,316 |
| 5 | Expeller ring | 029 | Cast iron | A49,Rubber,304,316 |
| 6 | Expeller | 028 | Cast iron | A49,Rubber,304,316 |
| 7 | Cover plate liner | 018 | Rubber | |
| 8 | Frame plate liner | 036 | Rubber | |
| 9 | Frame plate | 032 | Cast iron | Ductile cast iron |
| 10 | Cover plate | 013 | Cast iron | Ductile cast iron |
| 11 | Base | 003 | Cast iron | Ductile cast iron |
| 12 | 005 | | Assorted | |
