14Pcs Bar Type Long Jaw Wheel Bearing Hub Puller Tool

14Pcs 2 Size Bearing Separator Bearing Removal Puller

Bar-Type 2" 3" Splitter Long Jaw Gear Pulley

Features:

• 2 inches and 3 inches bearing separators.
• Drop forged and heat treated.
• Separator tools are used with bar puller and legs for a wide variety of pulling jobs
• The 5"" puller cross-bar with a 6-1/4"" forcing screw or each of the bearing separators may also be used separately or in combination with other pullers or tools.
• Blow mold case for storage.

Package Included (14pcs):

• Drop Forged Construction
• Two Bearing separator jaws (Splitters) - 2"" & 3""
• Extension Legs: 5"" - 4pcs
• Extension Legs: 4"" - 4pcs
• Yoke center adapter: 6"" – 1pcs
• Puller Head Bar: 6.9” – 1pcs
• Hooks: 2pcs
• Forcing screws
• Specifications:
• Material: Steel, Iron, Plastic
• Overall Size:14.5 x 9.4 x 2.4"" (LxWxH)
• G.W.: 12.98 Lb
• Quantity: 14 PCS

User Manual:
Assembly Precautions

• 1. Assemble only according to these instructions. Improper assembly can create hazards.
• 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
• 3. Keep assembly area clean and well lit.
• 4. Keep bystanders out of the area during assembly.
• 5. Do not assemble when tired or when under the influence of alcohol, drugs or medication.

Specific Safety Precautions

• 1. Be certain that the separator jaws are evenly set between bearing halves before attempting to separate.
• 2. Lead Screw (5)should be centered on the shaft where the bearings are being pulled to avoid damaging shaft or bearing housing.
• 3. Avoid pinching or scraping the bearing shaft by securely (and squarely) placing the Jaws around the bearing housing.
• 4. Use care when removing the Lead Screw from the Case to avoid damaging the threads. Pry up from the ends of the Lead Screw.

Operating Instructions
Pulling Bearings off Shaft

• 1. Select the proper size Bearing Separator Jaw (2 or 14) for the bearing size (2.2" ~ 3" or 2") being removed from the shaft.
• 2. Loosen the Separator Jaw Nuts (3) sufficiently to allow the jaws to catch behind the bearing housing.
• 3. Using a wrench (not included), begin to evenly tighten the Nuts until the jaws are securely set behind the bearing housing.
• 4. Screw in both Extension Screws of the same length (4/12 or 6/9) into the Bearing Separator

Jaws as shown below.
NOTE: Do not use Extension Screws of different lengths.

• 5. Place the 6 inch Yoke (16) over the Extension Screws and tightly secure with Washers (7) and Nuts (3).
• 6. Screw Lead Screw (5) into the Yoke until it touches the center of the shaft where the bearings are mounted.
• 7. Using a wrench, turn the Lead Screw clockwise until the bearing housing begins to move off the shaft.
• 8. Continue turning?the Lead Screw until the bearing housing is off the shaft.
• 9. Remove the Lead Screw by turning it counterclockwise.
• 10. Remove bearing housing.

YEEDA offers diverse automotive workshop equipment ,and is now also getting into Automotive,Industrial and Hardware market.

We Aim to provide you with quality products,solutions and outstanding service,to comply with our motto “Quality first, Quality last ” .

We put our tools through punishing test, which far exceed the strain of normal use, ensuring that our tools perform to professional standards and stay tough for long haul .

The owner of YEEDA believes that “trust is the biggest business in the world!” So We will continue to look at market opportunities, and share with Customers; We will continue to be innovative,and focus on product development with our customers.

We made a commitment to supply high quality dependable products for a reasonable price and provide customers the broadest selection of tools and equipment from a single source !