Through hole incremental encoder dimension 100mm shaft 63mm Z100
Non-bearing encoder
Matters needing attention
1. Must choose the power supply voltage: DC5V or DC8-30V
2. Must choose leaf spring plate model number if you select hollow
shaft encoder
3. Please advise the motor speed (RPM) that you actually use
4. If you have any other requirements, please provide detail
parameters
Model Number of Z100Series to select
Z100-J12C2500/8B40
Z100-C12E2500/10B42
Z100-J12C2500/16B45
Z100-C12E5000/8B48
Z100-J12C5000/10B46
Z100-C12E5000/16B50
Z100-J12C10000/8B52
Z100-C12E10000/10B55
Z100-J12C10000/16B60
Z100-C12E52500/8B63
Z100-J12C2500/10B40
Z100-C12E2500/16B42
Z100-J12C5000/8B45
Product introduction
| Items | Basic parameters |
| Brand | HENGXIANG |
| Encoder type | bearingless encoder |
| External diameter | 100mm |
| Thickness | 16mm |
| Hollow shaft type | through hole |
| Hollow shaft diameter | 40mm;63mm;65mm |
| Resolution | 2500/8；2500/10;2500/16;5000/10;5000/16; |
| 10000/8;10000/10;10000/16 |
| Output phase | A+,B+,Z+,A-,B-,Z-,U+,V+,W+,U-,V-,W- |
| Supply voltage | DC5V ; DC8--30V |
| Output mode | Radial cable |
| Radial socket |
| line drive (26LS31) TTL |
| line drive(DC8-30V) HTL |
| Cable length | 300mm |
| rise/fall time | less than 1 us(cable length:2 meters) |
| Consumption current | 120mA MAX |
| Top response frequency | 300KHZ |
| GND | not connect to encoder |
| Slew speed | 5000RPM |
| Environmental temperature | Operating:-20 ～+80°；storage:-25 ～+90° |
| Environmental humidity | Operating and storage: 35-85%RH(noncondensing) |
| Material | aluminum alloy |
| Certification | CE |
| package | Carton box |
| Net weight | About 180g (with package) |
Principle of encoder
Today most incremental encoders have a Push-Pull (HTL) or RS422
(TTL) output driver, these have replaced most of the older output
circuits like Open Collector NPN, Open Collector PNP, Voltage
Output.
Push-Pull (HTL) circuits, also known as Totem Pole, provide a
signal level which corresponds to the applied supply voltage. The
supply voltage typically ranges from 8 to 30 VDC.
With proper connections you can use the Push Pull interface to
replace true open collector circuits by using an external diode
connected in a way to limit the direction of the current for RS422
(TTL) circuits provide a constant 5 V signal level that is not
dependent on the supply voltage. Two supply voltage ranges can be
selected: From 4.75 to 5.5 VDC (can be used to replace open
collector output drivers) or from 8 to 30 VDC. Using differential
signals the output fully complies to the RS422 standard.
The differential outputs have the highest frequency response
capability and the best noise immunity. To ensure this the receiver
should also be a differential.
Replacement of Older Output Drivers
A logic gate interprets certain input voltages as high (logic 1) or
low (logic 0).
TTL (transistor-transistor-logic): A signal above 2 V is
interpreted as logic 1 and a signal less than 0.8 V is interpreted
as logic 0. The output voltage ranges between 0-5 V.
HTL (high-threshold-logic): A signal above 3 V is a logic 1 and a
signal less than 1 V is a logic 0. The high output signal level is
dependent from the supply voltage. Because of the higher voltage
difference between logic 0 and 1, the HTL logic is more immune to
interference and more resistant against electrical noise.
