Steel Coil Rail Car Suitable for Short-distance Slow-moving
Occasions
Suitable for short-distance, slow-moving occasions. In order to
reduce cable wear, it is suitable for applications with high
frequency and low vehicle height. The driving distance of this
series of steel coil rail car is generally less than 20 meters. In
the case of slow running speed and short driving distance, the
towline can be used to reduce cable wear. The mechanism is simple
and the cost is low. This is a common crosswalk plane in the
workshop. This car is suitable for applications where the frequency
of use is high and the height of the vehicle is low.
Safety Operating Regulations for Electric Flat Cars
1. The electric steel coil rail car can start smoothly only after
ringing the bell, and pay attention to the abnormal situation
around it, and be ready for parking at any time. No collision with
the rail stop at the end of the track is allowed.
2. Electric steel coil rail cars should be operated at a slower
speed and no quick change of direction is allowed.
3. Electric steel coil rail cars are not allowed to overload when
loading goods. The goods should be stacked evenly.
4. In case of sudden power failure, the control switch should be
restored to zero. After the electric steel coil rail car has
finished its work, it must cut off the power supply and unload the
load cleaning equipment.
Technical Parameters Of Steel Coil Rail Car Suitable for
Short-distance Slow-moving Occasions
| Model | BXC-2t | BXC-20t | BXC-50t | BXC-100t | BXC-150t |
| Rated Load(t) | 2 | 20 | 50 | 100 | 150 |
| Table Size(mm) | Length(L) | 2000 | 4000 | 5500 | 6500 | 10000 |
| Width(W) | 1500 | 2200 | 2500 | 2800 | 3000 |
| Heigth(H) | 450 | 550 | 650 | 900 | 1200 |
| Wheel Base(mm) | 1200 | 2800 | 4200 | 4900 | 7000 |
| Rail Inner Gauge(mm) | 1200 | 1435 | 1435 | 2000 | 2000 |
| Wheel Diameter(mm) | 270 | 350 | 500 | 600 | 600 |
| Wheel Quantity | 4 | 4 | 4 | 4 | 8 |
| Ground Clearance(mm) | 50 | 50 | 50 | 75 | 75 |
| Running Speed(min) | 0-25 | 0-20 | 0-20 | 0-20 | 0-18 |
| Motor Power(kw) | 1 | 2.2 | 5 | 10 | 15 |
| Battery Capacity | 180 | 180 | 330 | 440 | 600 |
| Battery Voltage | 24 | 48 | 48 | 72 | 72 |
| Running Time When Full Load | 4.32 | 4 | 3.3 | 3.2 | 2.9 |
| Running Distance for One Charge(Km) | 6.5 | 4.8 | 4 | 3.8 | 3.2 |
| Max Wheel Load(KN) | 14.4 | 77.7 | 174 | 343.8 | 265.2 |
| Reference Weight(t) | 2.8 | 5.9 | 8 | 14.6 | 26.8 |
| Recommended Rail Model | P15 | P24 | P43 | QU100 | QU100 |
Rust Removal and Painting Requirements for Electric Steel Coil Rail
Cars:
1. The film thickness of each layer of electric flat car is 25-35
micron, and the total film thickness is 75-140 micron.
2. Party B shall process and manufacture electric flat cars in
strict accordance with technical requirements and design drawings,
and make self-inspection records.
Electric Steel Coil Rail Car assembly requirements:
The moving end of the two wheelset bearings of the electric flat
car shall be installed on the same side of the vehicle.
General technical requirements for electric Steel Coil Rail Cars
(materials):
The mechanical properties of the reducer shell materials for
electric steel coil rail cars shall not be lower than those of
HT200 in GB 9439.
General Technical Requirements for Electric Flat Cars (Frame)
Automatic submerged arc welding for electric flat car welding.
