2016998-001 GE Dual Reusable Temperature Adapter Cables For 400
Series ,50cm(20 Inch)
Two temperatures are measured by two functions. It ensures the
alarm of the patient with adjustable high and low temperature
limits. There are system alarms for sensor and calibration errors.
The temperature connector and measurement circuit are used in
conjunction with the cardiac output monitor function. So you cannot
use both functions at the same time. The signal in the patient
cable indicates proper operation.
Temperature calibration
NOTE: For the temperature calibration, separate, accurate test
plugs (25 °C and 45 °C) are needed. A test set of two plugs is
available from GE Healthcare, order code 884515-HEL. A Dual
temperature adapter cable, order code 2016998-001 is also required
for the temperature calibration. Calibrate the temperature, when
the measured test values differ for more than ±0.1 °C, and always
after STP board replacement.
1. Enter the STP service menu. (Monitor Setup - Install/Service
(password 16-4-34) - Service (password 26-23-8) - Parameters).
2. Enter Calibrations menu.
- Choose Protection OFF in protect mode.
- Select Calibrate T1/Calibrate T2.
- Insert calibration plug (25 °C) into T1/T2 connector.
- Push the ComWheel.
- Insert calibration plug (45 °C) into T1/T2 connector.
- Push the ComWheel.
9. Choose Protection ON in protect mode
GE Dual Reusable Temperature Adapter cables for 400 series ,50cm(20
inch) 2016998-001 specification
| Product Name | GE Dual Reusable Temperature Adapter cables for 400 series ,50cm(20
inch) 2016998-001 |
| Brand | GE |
| Part No | 2016998-001 |
| Use for | 400 Series |
| Probe length | 50cm(20 inch) |
Temperature test producer
1. Set the temperature output of the patient simulator to 37° C.
2. Connect the temperature adapter cable to the TEMP/CO connector
of the patient monitor.
3. Set the switch on the temperature adapter to the 400 or 700
position according to customer preference.
4. Connect the 400 or 700 series temperature output connector of
the patient simulator to the T1 connector of the temperature
adapter.
5. Check that the TEMP parameter window appears on the patient
monitor display with a T1 reading of 37.0° ± 0.4° C.
6. Move the temperature simulator cable from the T1 connector of
the temperature adapter to the T2 connector of the temperature
adapter.
7. Check that the T2 reading in the TEMP parameter window on the
patient monitor display is 37.0°±0.4°C
Two temperatures are measured by two functions. It ensures the
alarm of the patient with adjustable high and low temperature
limits. There are system alarms for sensor and calibration errors.
The temperature connector and measurement circuit are used in
conjunction with the cardiac output monitor function. So you cannot
use both functions at the same time. The signal in the patient
cable indicates proper operation.
Temperature calibration
NOTE: For the temperature calibration, separate, accurate test
plugs (25 °C and 45 °C) are needed. A test set of two plugs is
available from GE Healthcare, order code 884515-HEL. A Dual
temperature adapter cable, order code 2016998-001 is also required
for the temperature calibration. Calibrate the temperature, when
the measured test values differ for more than ±0.1 °C, and always
after STP board replacement.
1. Enter the STP service menu. (Monitor Setup - Install/Service
(password 16-4-34) - Service (password 26-23-8) - Parameters).
2. Enter Calibrations menu.
- Choose Protection OFF in protect mode.
- Select Calibrate T1/Calibrate T2.
- Insert calibration plug (25 °C) into T1/T2 connector.
- Push the ComWheel.
- Insert calibration plug (45 °C) into T1/T2 connector.
- Push the ComWheel.
9. Choose Protection ON in protect mode
GE Dual Reusable Temperature Adapter cables for 400 series ,50cm(20
inch) 2016998-001 specification
| Product Name | GE Dual Reusable Temperature Adapter cables for 400 series ,50cm(20
inch) 2016998-001 |
| Brand | GE |
| Part No | 2016998-001 |
| Use for | 400 Series |
| Probe length | 50cm(20 inch) |
Temperature test producer
1. Set the temperature output of the patient simulator to 37° C.
2. Connect the temperature adapter cable to the TEMP/CO connector
of the patient monitor.
3. Set the switch on the temperature adapter to the 400 or 700
position according to customer preference.
4. Connect the 400 or 700 series temperature output connector of
the patient simulator to the T1 connector of the temperature
adapter.
5. Check that the TEMP parameter window appears on the patient
monitor display with a T1 reading of 37.0° ± 0.4° C.
6. Move the temperature simulator cable from the T1 connector of
the temperature adapter to the T2 connector of the temperature
adapter.
7. Check that the T2 reading in the TEMP parameter window on the
patient monitor display is 37.0°±0.4°C
8.Remove the temperature adapter and temperature simulator cable
from the patient monitor and patient simulator.
If you're interested in 2016998-001 GE Dual Reusable Temperature Adapter Cables For 400
Series ,50cm(20 Inch) ,feel free to contact us .Thank you.
