1, Detailed product characteristic
| Basic demission information |
| Flammability | UL94V-0 |
| Application | Dual, wire-to-board |
| Pitch | 2.50mm |
| Color | Black |
| Material | PBT |
| Bump | With and without type available |
| Wire range | AWG22# to 28# |
| Wire insulation diameter | 1.63mm Max. |
| Terminal materials | Brass material, tin-plated or gold-flash finish |
|
| Electrical properties |
| Current Rating | 3.0 A AC, DC |
| Voltage Rating | 250 V AC, DC |
| Contact Resistance | 20 mΩ Max |
| Insulation Resistance | 1000 MΩ min |
| Withstanding Voltage | 1500V AC/minute |
|
| Mechanical properties |
| Temperature range | -25℃ to 85 ℃ |
| Other information please kindly check the following picture. |
2, Engineering drawing and testing report
Folllowing pictures are out testing report and exact engineering
drawing for your information, please kindly check it, wish it can
help you to get what you really need.
With one nose type
Environmental Performance And Others
| Test Description | Procedure | Requirement |
| 6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) |
| 6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond.
A) | Appearance No Damage. Contact Resistance 40mΩ (Max.) |
| 6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) |
| 6-4 | Humidity | Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) | Appearance No Damage. Contact Resistance 40mΩ (Max.) Insulation Resistance 100MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 |
| 6-5 | Temperature Cycling | 5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025) | Appearance No Damage. Contact Resistance 40mΩ (Max.) |
| 6-6 | Salt Spray | Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt
spray from the 5±1% solution at 35±2℃. (Based upon JIS
C0023/MIL-STD-202 Method 101D Cond. B) |
| 6-7 | SO2 Gas | 24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. |
| 6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia
solution. |
| 6-9 | Solderability | Soldering Time: 5±0.5 sec. Solder Temperature: 245±5℃ | Solder Wetting 95% of immersed area must show no voids, pin holes |
| 6-10 | Resistance to Soldering Heat (DIP) | Solder pot method Soldering time: 10±0.5 sec. Solder Temperature: 260±5℃ Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ | Appearance No Damage. |
| 6-11 | Resistance to Soldering Heat (SMT) | When reflowing Refer to paragraph 8 Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ | Appearance No Damage. |
3, Application fied of these product
This product is designed and msde for PDP, LCD, or small
electronics equipment. Because we can controll NPL ratio under a
very low value, so our parts are accepted by famouse and
international company like TPV, Emerson, Amphenol Corporation,
Skyworth, etc. You can know this directly from the attached
pictures. By the way, all product are approved by REACH, UL, RoHS.
In order to protect the evironment, some parts are halogen free.
4, Our service
We offer one-stop service for you, it will help you to make cost
down.Our payment way is flexible according to order sales amount.
Q:Do you allow multiple design per setup?
A:Yes.We accept OEM service and allow multiple design per setup.
Q:How long does shipping take?
A:It depends on the destination location and quantity. In most
developed world, delivery by Fed x/UPS/DHL is normally 2-3
days(excluding weekends).
Q: How is the goods packaged ?
A: Usually in vacuum packages and carton box.
