15KW Copper Wire Making Machine 5.5KW Spooler Motor For Drawing And Annealing

HXE-22DT Fine copper wire drawing machine with Annealer & Double spoolers

I. Quick Description

22DT Fine copper wire drawing machine with annealer & double spoolers is used to draw and annealing single bare copper wire from 0.8mm-1.4mm to 0.1mm-0.6mm.

II. Components

III. Main Technical parameters

1. Usage single bare copper wire drawing and annealing

2. Inlet size Ф0.8mm-Ф1.4mm

3. Outlet size Ф0.1mm-Ф0.6mm

4. Machine speed/max 1500m/min

5. Die number 22, Dies size 25mm×8-10mmT, Slip ratio 15.5%+8%

6. Wire drawing mode standing-mode and 4axes

7. Drive: by Inverter control, Brand Inovance, Chinese famous brand.

8. Main motor 15KW, Spooler motor 5.5KW*1set/2sets

9. Annealing voltage DC55V/max

10. Annealing current DC600A/max

11. Annealing power 33KVA

12. Annealing method D.C three-section annealer

13. Quantity of steam 8kg/h

14. Capacity of compressed air 0.4-0.6Mpa,15L/min

15. Demand Water quantity for annealing and coolant 150L/min

16. Machine frame welded by steel plate

17. Transmission By Timing belts

18. Capstan ceramic plasma

19. Lubricating system Spray

20. Bobbin size 300mm, loading capacity :50kg/max (Can be customized)

21. Bobbin loading &unloading type shaft type

22. Traversing unit 110W synchros motor, width: 270mm/max

23. Bobbin controlling Fixed by Screw

24. Brake 20KG-M magnetic brake

25. Operation panel &control cabinet 1000×800×1800mm

26. Machine dimension 2100mm*1600mm*1700mm

27. Machine weight 3200KG

IV. Attention

4-1. If wire breaks, will stop automatically, and the Fault Indicator light will open.

After connect the wire, press the Fault Reset button(Yellow button) and the On button (Green button), to run the machine again.

4-2. Press Emergency Stop button(Red button) to shut down the machine immediately.

After solve, press the button again to run the machine.

4-3. After set the Length-counter, the machine will stop automatically when reach the length set.

After change the Spool, please press the Length Reset button(Yellow button) and the Spool Reset button(Yellow button) to run the machine again.

4-4. After the machine stop(no running at all), then switch the Pump switch to stop the lubrication.

4-5. Do not touch the wire in the Annealing section.

4-6. After shut down the machine, need at least 30 seconds to restart the machine.

4-7. Wire often breaks, adjust the speed, balance arm, check the dies are clean or not.

4-8. If has scratch on the surface of the wire, check the capstans on the Take-up part. Check the drawing capstans.

V. Advantage and after-sale service

A: Advantage

(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.

(2). Body and other key components and parts are produced by our own factory , quality is reliable.

(3). DC. three-section annealing

(4). Our company’s developing process in more than 10 years.

B: After-sale service

Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:

(1) 1 year for mechanical part.

(2) 6 month for electrical part.

Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.

1. Due to wrong operation while shipping.

2. Due to Buyer`s wrong preparation that may cause damage to the machine.

3. Due to Buyer`s wrong operation that may cause damage to the machine.

4. Not in the consuming part list.

5. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.

6. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.

7. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.

      Suzhou Hengxie Machinery Co., Ltd was established in 2005, a total professional in drawing machine field, specialized in copper and aluminium wire drawing machines. Located in Suzhou City, very close to Shanghai, we share a convenient transportation and the most successful working environment.

Our 6,700 square meters of land allows producing a wide range of equipment, developing and researching new products. We always strive to introduce the latest international techniques to update our products.

With management concept of “Excellent quality, Reasonable prices, Superior services”, our hope is to not only meet our customers` expectations but to exceed them.

Here are the machines we have: Copper&Aluminium Rod Breakdown machine, Large and intermediate wire drawing machine with online annealer, Intermediate wire drawing machine, Intermediate wire drawing machine with online annealer, Fine wire drawing machine, Fine wire drawing machine with online annealer, Customized fine wire drawing machine with annealer, Super fine wire drawing machine. As long as we talk, we can always meet your detail requirements.

Our market includes both domestic and overseas. Such as Bangladesh, Egypt, Iran, Malaysia, Syria, Algeria, Kenya, Turkey, South Africa, Latin America and so on.

With the concept of “Stable quality and mutual development”, Hengxie welcome all customers from the world to create a sincere cooperation and win-win benefit in the future.