22 Dies High Speed Wire Drawing Machine With Flat Belts And Timing Belts Transmission

HXE-22DT Fine copper wire drawing machine with annealing machine

I. Usage

HXE-22DT Fine copper wire drawing machine with annealer is used to draw and anneal single bare copper wire from 0.6mm-1.2mm to 0.1mm-0.32mm.

II. Main Technical parameters

1. Usage single bare copper wire drawing and annealing
2. Inlet size 0.6mm-1.2mm
3. Outlet size 0.1mm-0.32mm (Elongation of finished annealed wire 20% to 30%)
4. Machine speed/max 2000m/min
5. Die number 22, Dies size 25mm×8-10mmT, Slip ratio 15%+8%
6. Wire drawing mode standing-mode and 4axes
7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine
8. Main motor 11KW, Spooler motor 3.7KW, China best brand
9. Annealing voltage DC50V/max, Annealing current DC300A/max, Annealing power 15KVA
10. Annealing method DC Three section annealing
11. Annealing protection will be done by steam protection
12. Capacity of compressed air 0.4-0.6Mpa, 20L/min
13. Demand Water quantity for annealing and coolant 200L/min
14. Machine frame welded by steel plate
15. Transmission Flat belts
16. Capstan Ceramic plasma17.Lubricating system Pipe Spray
18. Bobbin size 300mm, loading capacity: 50kg/max
19. Bobbin loading & unloading type shaft type
20. Traversing unit 110W synchros motor, width: 270mm/max
21. Tension control by Air pressure tension control (With Weight balance as Backup)
22. Cabinet 0.8m*0.6m*2.0m
23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m
24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.

III. Components

IV. Preparation before working

4-1. Check all parts lubrication conditions,

4-2. Check drawing lubrication oil, cooling water, steam, air pressure.

4-3. After checking, connect to power, according to the Electrical drawing, use foot switch, to make the machine operating in low speed (under 4m/s), if no Abnormal, then can begin to work.

V. Operating procedures

5-1. Open power switch

5-2. According to the wire diameter, choose the dies (Check the die list).

5-3. Use pliers to break the wire to get a smaller section.

5-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).

5-5. Wire direction, please check the Drawing for Wire path.

5-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.

5-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.

5-8. Set the length meters, then press the Start button to start the machine.

      Suzhou Hengxie Machinery Co., Ltd was established in 2005, a total professional in drawing machine field, specialized in copper and aluminium wire drawing machines. Located in Suzhou City, very close to Shanghai, we share a convenient transportation and the most successful working environment.

Our 6,700 square meters of land allows producing a wide range of equipment, developing and researching new products. We always strive to introduce the latest international techniques to update our products.

With management concept of “Excellent quality, Reasonable prices, Superior services”, our hope is to not only meet our customers` expectations but to exceed them.

Here are the machines we have: Copper&Aluminium Rod Breakdown machine, Large and intermediate wire drawing machine with online annealer, Intermediate wire drawing machine, Intermediate wire drawing machine with online annealer, Fine wire drawing machine, Fine wire drawing machine with online annealer, Customized fine wire drawing machine with annealer, Super fine wire drawing machine. As long as we talk, we can always meet your detail requirements.

Our market includes both domestic and overseas. Such as Bangladesh, Egypt, Iran, Malaysia, Syria, Algeria, Kenya, Turkey, South Africa, Latin America and so on.

With the concept of “Stable quality and mutual development”, Hengxie welcome all customers from the world to create a sincere cooperation and win-win benefit in the future.