1. Descriptions:
Nylon Hammer Plug Anchors with nail screws are made of Nylon material.The screws are steel
made with countersunk head. Nylon Hammer Plug Anchors with nail
screws are pre-assembled through fixing, a light duty nail
expanding for solid masonry, perforate bricks and hollow blocks
constructions.They are also used in All kinds of timber including
laths, frames, wall connection or render profiles, skirting boards,
wall angles, cable ducts, cable and pipe clips, sheets etc.
Crever Fastener Factory provide standard and non-standard Hammer
Plug Anchors with nail screw,wall plug anchors,Rawl plugs,fixing
ties with Plastic/PP, Nylon/PE,PA materials.Special style,body
colour and size is avariable as customers’ needings.
2. Product Specifications:
1. Name: nylon hammer anchor nail screw, nylon hammer fixing anchor
2. Grade: C10B21, C1022,
SUS201,SUS410,SUS304,SUS316,A2-70,A2-80,A4-80
3. Size: M5x30--M10x220
4. Standard: DIN ISO
5. Certification: ISO9001, SGS, CTI, ROHS
Product Name | nylon hammer anchor with nail screw |
Material | stainless steel, carbon steel, alloy steel, brass and so on |
Color | zinc, black phosphate, gray, decramet, HDG, ruspert, nickel and so
on |
Standard | DIN GB ISO JIS BA ANSI |
Grade | C10B21, C1022, SUS201, SUS304, SUS316, A2-70, A2-80, A4-80, 4.8 6.8
8.8 10.9 12.9 |
Sizes | M5x30mm--M10x220 |
Thread | full thread, partical thread |
Drive | philips, pozi, socket, hex, square, solloted, combined |
3. FAQ:
What is a nylon nail anchor?
Nylon nail anchor are light duty, drive type expansion anchors.
They come preassembled and are ready to be installed. Once the nail
is set in the anchor body, it is tamper resistant.
When should I use one?
These can be used for light duty fastening in many materials,
including concrete, block, and brick.
What materials are used to make these anchors?
The body is made of a rust resistant material called polyamide
nylon. The nail is available in either zinc plated carbon steel or
aluminum.
Is this nail anchor available with a stainless steel nail?
Yes, it can come with both carbon steel and stainless steel nail.
What styles are available?
These are available in three head styles: flat countersunk, round,
and mushroom.
What sizes of nylon nail-its are available?
It is available in two different diameters: 3/16” and 1/4”. The
3/16” diameter is available in lengths of 3/4”, 1”, and 1-1/2”. The
1/4” diameter is available in lengths of 1”, 1-1/2”, 2”, and 3”.
Why is the body on anchor split?
It is split to allow the anchor body to move apart as the nail is
forced down into the anchor body, which creates expansion force
against the base material.
How do I install a nylon nail-it?
Installation is simple. Drill a hole, insert the anchor through the
item being installed, and set it with a hammer. Once the nail is
flush with the head, the anchor is fully expanded and properly set.
How deep do I drill the hole?
The hole must be at least 1/4” deeper than the expected embedment
in the base material.
Do I have to clean the hole out before installation?
Yes. Any concrete dust or debris in the hole may reduce the holding
values of the anchor. Cleaning the hole will ensure a better chance
for a quality fastening.
Can I insert it through the hole in the fixture and into the hole
in the base material?
Yes, it can be installed through the fixture into the concrete, and
hole spotting is not necessary. Make sure that the hole in the
fixture is slightly larger than the designated diameter of the
anchor being installed.
Can these anchors be used in extremely cold environments?
It is not advised to use them in cold environments, as the anchor
can become very brittle. This may cause the nylon anchor body to
shatter during installation or, even when installed properly, to
have reduced holding values.
Can I use them in very wet environments?
The body will not rust. If the nail is zinc plated carbon steel
then it will rust, but the aluminum nail and the all-nylon nail
will not rust.
Can I install one for an overhead application?
No, they should not be used for overhead installations.
4. More pictures:
NYLON HAMMER ANCHOR
