High Precision Voltage Current Loop Calibrator Handheld Auto Signal
Generator
VICTOR 05S Loop Calibrator high precision Voltage Current
Simulation transmitter handheld automatic signal generator
VC05S LOOP Calibrator
Basic characteristics of the product
- Input measurement characteristics
DC voltage DCV, DC current DCI
- The maximum measurement accuracy is 0.05% and the measurement
display is 5 digits.
- Measurement rate: 2-3 times/sec.
- Loop detection function, internal 24V circuit power supply, and
simultaneous measurement of current.
- mA has a percentage display mode.
- Analog output characteristics
DC current DCI
The maximum measurement accuracy is 0.05% and the measurement
display is 5 digits.
- Output settings can be manually increased or decreased by position.
- DCI output includes active output (internal 24V power supply) and
passive output (external 24V power supply).
- mA has a percentage display mode.
- During DCI output, it can provide manual stepping and automatic
waveform output functions.
The manual stepping output mode includes: 25% stepping and 100%
stepping.
The output current is selectable from 0~20mA or 4~20mA.
Automatic wave output type includes: automatic step, sawtooth wave,
triangle wave, and automatic waveform working parameters can be
configured.
- Internal 24V circuit power supply.
- It has maintenance setup functions, including
Auto power-off, backlight, flashlight
- The segment code is displayed on an LCD with a white backlight.
- It has a LED flashlight for lighting.
- It is powered by 3 AA battery cells. The battery compartment door
is convenient for battery replacement. Low-battery detection is
available.
- It is small, firm, reliable, suitable for field use, and cheap.
- User-optional large-suction magnetic sling is provided.
II. Basic function and performance of the product (technical index)
Analog measurement function [Used within one year after calibration, 23 ℃± 5 ℃, 20-70% RH,
accuracy=± (% set value+% reading)]
| Output function | Range | Output range | Resolution | Accuracy | Remarks |
DC current DCI | 30mA | 0.000mA~30.000mA | 0.001mA | 0.05%+4uA | At 20 mA, maximum load 1000Ω resistance When simulating the transmitter, the external circuit power supply
is 5~28V |
Other characteristics:
- Uncertainty includes standard uncertainty, hysteresis,
nonlinearity, repeatability, and typical long-term stability over
the period mentioned (K = 2).
- Maximum applied voltage at input end: about 30Vpk; Maximum applied
current at input end: about 25mA
- The temperature range of internal temperature compensated sensor
RJC is -10 to 50°C. The temperature measurement accuracy at 18 to
28°C is ±0.5°C, and the temperature measurement accuracy at other
temperature is ±1°C. Cold end compensation time is 10S/ times.
- Temperature coefficient: 0.1 × basic accuracy/℃ (temperature range
< 18℃ or > 28℃)
Input output function [Used within one year after calibration, 23℃±5℃, 20-70% RH,
accuracy =+/-(% set point + reading %)]
| Measurement function | Range | Measurement range | Resolution | Accuracy | Remarks |
DC voltage DCV | 35V | -35.000V~35.000V | 0.001V | 0.02%+2mV | Input resistance: approximately 1MΩ |
DC current DCI | 30mA | -35.000mA~35.000mA | 0.001mA | 0.02%+4uA | Shunt resistance: approximately 10Ω Input resistance: approximately 20Ω |
Loop power supply LOOP | 24 V | | | 10% | Short circuit protection Maximum current: 22 mA Maximum input voltage: 60 V DC |
Other characteristics:
- Uncertainty includes standard uncertainty, hysteresis,
nonlinearity, repeatability, and typical long-term stability over
the period mentioned (K = 2).
- Display refresh rate: 2~3 times / second.
- Maximum applied voltage at input end: 60 Vpk; Maximum applied
current at input end: 50mA.
Current input protection: 100mA/250V Fast FUSE
- Input common-mode rejection: 50Hz /60 Hz > 120 db; Input
serial-mode rejection: 50Hz /60 Hz > 60 db
- The temperature range of internal temperature compensated sensor
RJC is -10 to 50°C. The temperature measurement accuracy at 18 to
28°C is ±0.5°C, and the temperature measurement accuracy at other
temperature is ±1°C. Cold end compensation time is 10S/ times.
- Temperature coefficient: 0.1 × basic accuracy / ℃ (temperature
range <18℃ or >28℃)
III. General characteristics of the product
- Operating temperature and humidity: 0 to 50ºC ≤80%RH without
condensation; 40 to 50ºC ≤70%RH.
- Storage temperature and humidity: -25 to 60ºC ≤90%RH without
condensation.
- Electrical safety: EN61010-1:2001
Withstand voltage: AC3540V(50/60Hz)/5 seconds between terminal and
housing.
Insulation impedance: DC1000V/100MΩ or more between terminal and
housing.
- Electromagnetic compatibility (EMC): EN61326-1:2006
Performance criterion 2 is met, i.e. the function and performance
are temporarily reduced or lost, but can be recovered by
themselves.
- Protection grade IP40.
- Vibration and fall: IEC 60068-2-64:2008, IEC 60068-2-32:2008
Random, 2g, 5-500Hz; 1m drop test.
- CE certification.
- Quality standard: developed, designed and manufactured in
accordance with TUV ISO 9001.
- Calibration period and preheating time:
To ensure the accuracy of the Table, the calibration period is one
year.
The startup preheating time is more than 30 minutes.
- Instrument display and key
Segment code LCD display, white backlight
Rubber key is adopted
3 pcs of AA alkaline batteries for power supply
IV. Peripheral configuration of the product
Industrial test conductor: 2 pairs
User’s Manual: 1 manual
AA alkaline battery: 3 pcs
Graphic carton: 1 item
Fuse: 2 pieces
