High Speed 3 Ply Automatic Corrugated Cardboard Production Line
Main technical parameters and requirements in production line
1.type:WJ150-1800-I type three layer corrugated paperboard
production line:
2.The maximum production width of the corrugated cardboard:1800mm
3.Design speed:150m/min
4.Economic speed:80-120m/min
5.note:Production line speed test paper should meet the following
requirements:(the surface temperature of the equipment is not less
than 172℃)
6.Paper rating of not less than B grade ﹡Paper moisture content of
about:11%±2%
7.top paper:100—250g/m2 ﹡core paper:100--250g/m2
8.corrugated paper:100—150g/m2
Customer-owned section
1.steam heating system:proposal with 4000Kg / Hr of a steam boiler
pressure:1.25Mpa steam pipeline.
2.air compressed machine,air pipeline,glue conveying pipe.
3.power supply,wires connected to the operation panel and line
pipe.
4.water sources,water pipelines,buckets and so on.
5.Water, electricity, gas flush mounting civil foundation.
6.Test with the base paper,corn starch (potato),Industrial use
caustic soda,borax and other material.
7.Oil equipment,lubricating oil,hydraulic oil,lubricating grease.
8.installation,commissioning of food, accommodation.And provide
installers with the installation.
※ZJ-V5B hydraulic shaftless mill roll stand
※structural feature:
★adopt hydraulic drive to complete the paper clamping, loosen,
remove for the medium, translation left and right and others,the
lifting of the paper adopts hydraulic drive.
★brake adjustable adopts multipoint braking system.
★every stand matched two sets paper car , and they can paper on the
both sides at the same time.
※technical parameters:
1,the range of clamping paper:MAX1800mm MIN1000mm 2,clamping
diameters:MAX￠1500mm MIN￠350mm
3,main shaft diameter of paper holder:￠240mm 4,gas source work
pressure(Mpa):0.4---0.8Mpa
5,equipment size:Lmx4.3*Wmx1.8*Hmx1.6 6,single weight:MAX4000Kg
※structural feature:
★the whole track buried,The main frame of the 14th Channel steel
with ¢ 20mm cold drawn welded round,length of track6000mm.
★each paper holder matched two sets paper trolley, and paper on
both sides at the same time.pull the roller paper to the right
place.
Mainly purchased parts, raw materials and origin
Name of main parts
| Brands or place of origin | material |
track and paper car
| Tanggang or jigang | NO14channel steel,Q235A,steel strip |
bearing
| HRB,ZWZ,LYC | |
※structural features:
★preheat roller accord the pressure container national
standards,and enclose the pressure container certificates and
inspection certificate.
★Each roller surface after grinding precision grinding and dealing
with hard chrome plating, Surface friction is small, durable.
★electromotion adjustment angle, and angle can rotation adjustment
the preheat area in the range of 360°
※SF-320C fingerless type single facer
※structural feature:
★adopt hood suction structure,matched high pressure powerful fan.
Gas supply and electrical control cabinet to focus on the same
operation, the operating side full cover closed.
★High quality resin sand casting,wall thickness 200mm.Adopt
independent gear box, Universal joint transmission structure.
★install the lifting trolley on the conveyor bridge,Need to use the
car will tile roll assembly and pressure roller, such as convenient
and quick.
★Glue roller unit structure with the overall relocation,Maintenance
can sway the machine at the overall maintenance,improve the working
efficiency.
★The humidity control apparatus equipped with a spray, so flute
type to maintain good stability of deformation, avoid dry.
※technical parameters:
1.effective width:1800mm
2,operate direction:left or right(Determined in accordance with the
customer's facility)
3,design speed:150m/min
4,range of temperature:160—180℃
5,air source:0.4—0.9Mpa
6,steam pressure:0.8—1.3Mpa
7equipment:Lmx3.5*Wmx1.7*Hmx2.2
※Roller diameter parameters:
1,corrugated roller:up￠313mm down￠316mm pressure roller:￠320mm
2 ,glue roller:￠240mm fixed paste roller: ￠140mm preheat
roller:￠402mm
SM-F type double facer
※ structural feature:
★Heating plate surface by grinding treatment,hot plate width600mm,a
total of 14 pieces heating plate.Minister of cooling setting 4 m.
Preheat board is made of container board, in accordance with the
national standard of pressure container, enclosed the pressure
container certificate and inspection certificate.
★Hot plate with intensive gravitational roll structure.Pressure
roller with lifting hydraulic structure
★heat pipe of the heating board seven section of control
temperature, temperature display.
★up cotton belt with double cylinder S cotton belt tensioning
device.
Mainly purchased parts, raw materials and origin
Name of main parts
| Brands or place of origin | Material and type |
Main skeleton
| Tiangang or laigang production profile | NO36Channel steel and NO 16I-beam |
Heating plate
| Tiangang or jigang | Q235B Container board production |
Main drive motor
| Hebei hengshui | 45KW frequency motor |
Cotton belt
| Shenyang fuly | Cotton belt thickness 10mm |
traps
| Beijing traps | Inverted bucket |
contacts
| France Schneider | |
Hydraulic station
| Hebei | |
bearing
| HRB,ZWZ,LYC | |
Seat belt bearing
| Zhejiang wuhuan | |
Driving wallboard
| Hebei | HT250 |
Pneumatic elements
| Zhejiang Sonor CSM | |
Proximity Switch
| Korea Autonics | |
※NCBD thin blade slitter scorer(Zero Pressure Line)
※Structural features:
★Synchronous servo motor control row of knives, cable. Automatic
reset. Precise dimensions.change order time 3-8 seconds,the two
machines can be achieved with no slow down immediately for a single
memory of 999 order,non-stop automatic change order or manual
change order can be realized.
★Schneider M258PLC control system, using CANopen line system, with
order management capabilities, with the dryer speed synchronous
signal input.
★HMI with 10.4-inch color touch screen, storage 999 orders, change
orders automatically or manually for a single, fault alarm.
★Three kinds of pressure line forms:Convex against the
concave(three layers line),Convex against the concave(five layers
line),Convex against Flat,Three kinds of electric pressure line
forms can be converted.Crimping round shades by computer
control,linear, and easy to bend.
※Technical parameters:
1, working width:1800mm 2,operation direction:left or
right(Determined in accordance with customer plant)
3,the highest machinery speed:150m/min 4,Mechanical
configuration:Zero pressure line thin blade slitter scorer 5 knives
8 lines
5,The minimum width of the cutter:135mm The maximum width of the
cutter:1850mm
6,The minimum distance between the indentation:0mm
7,Cutter wheel positioning accuracy: ±0.5mm
More details pls add me
WhatsApp:+8613363699514
E-mail:anna@yikegroup.net
Anna CEO OF YIKE GROUP
