BP93420IB Pressure Transmitter sensor
Introduction of pressure transmitter sensor:
BP93420IB pressure transmitter sensor is the use of piezoresistive
effect principle, The diffused silicon pressure sensor uses the
piezoresistive effect principle, adopts the integrated technology
through doping and diffusion, along the characteristic crystal
direction on the monocrystalline silicon sheet, makes the strain
resistance, and forms the Wheisser bridge. By using the elastic
properties of silicon material, the anisotropic micromachining on
all kinds of silicon materials is made up of a diffused silicon
sensor which integrates force-sensitive and electrodynamic
conversion detection
Product Features of pressure transmitter sensor:
1. The piezoresistive effect of this force resistor in silicon chips
has no dead zone in the low range near zero point, and the range of
the pressure sensor can be as small as a few Kpa.
2. High output sensitivity
3. High precision, all stainless steel structure.
4. The chip adopts an integrated process and has no transmission
parts, it is small in size and light in weight
Applications of pressure transmitter sensor:
1. Pressure measurement of non-corrosive gases and liquids with
316L stainless steel
2. Applied in the marine and aviation industries
3. Used in industrial on-site processes such as petroleum,
chemical, metallurgy, power generation, and hydrology
4. Utilized in hydraulic and pneumatic control systems
Performance Parameters of pressure transmitter sensor:
| Measurement Range | -100kPa…0kPa ~ 10kPa…100MPa |
| Pressure Type | Gauge Pressure, Absolute Pressure, Sealed Pressure |
| Overload | ≤ 1.5 times of the rated range |
| Accuracy @ 25ºC | ±0.25% (Typical) ±0.5% (Maximum) |
| Repeatability | 0.1%FS |
| Hysteresis | 0.1%FS |
| Long-Term Stability | ±0.1%F.S/Year(Typical) ±0.2%F.S/Year(Maximum) |
| Zero Point Temperature Drift | ±0.03%F.S/ºC(≤100KPa) ±0.02%F.S/ºC(>100KPa) |
| Full Scale Temperature Drift | ±0.03%F.S/ºC(≤100KPa) ±0.02%F.S/ºC(>100KPa) |
| Compensation Temperature | 0-70ºC(≤10mpa,customizable) |
| Operating Temperature | -20ºC~80ºC |
| Storage Temperature | -40ºC~120ºC |
| Vibration | 10g,55Hz ~ 2kHz |
| Housing Material | 304,316L |
| Diaphragm Material | 316L |
| Insulation Resistance | 100MΩ 100VDC |
| Explosion-proof Rating | Ex db IIC T6 Gb |
| Protection Rating | IP65 |
| O-Ring Seal | Fluoro rubber |
| Weight | ~0.15kg |
| Output Signal | Supply Voltage | Output Type |
| 4~20mA | 12~30VDC | 2/3/4 wire |
| 0~10/20mA |
3 wire |
| 0/1~5V |
| 0/1~10V |
| 0.5~4.5V | 5VDC |
| Ordering tips of pressure transmitter sensor |
1. When selecting the product, please ensure that the tested medium
is compatible with the contact part of the product.
2. When placing an order, please note that explosion-proof products
do not include digital display heads.
3. When ordering with LCD or LED display head of transducer,
transmitter power should not be less than 20 VDC.
4. In order to ensure the reliable operation of the product, it is
recommended that users install lightning protection devices on site
and ensure that the product and power supply are reliably grounded.
5. The rated operating temperature range of fluorine rubber O-ring
is -20℃~ 250℃. When the operating temperature of the product is
lower than -20 ° C, EPDM O-type sealing ring should be selected.
6. The default cable length is 1.5m and there are three kinds of
materials to choose from. If there are no special instructions, no
cable or polyethylene cable material can be used. If you need a
different cable material, please specify it in the order form.
7. In case of strong vibration, instantaneous impact force, strong
electromagnetic or radio frequency interference and other special
requirements, please inform our company and indicate in the order.
| Order Guide of pressure transmitter sensor |
| BP93420XX | Pressure Transmitter |
| Code | Outline Construction |
| IB | General Pressure Transmitter | IX | Display Pressure Transmitter |
| IE | Shock-resistant Aviation Pressure Transmitter | IIC/III | Industrial General/ Display Pressure Transmitter |
| IF | Moisture-proof Pressure Transmitter | IIE/IIIE | General/Display Pressure Transmitter |
| IN | Air Conditioning Dedicated Pressure Transmitter | | |
| IC | High-temperature Pressure Transmitter | | |
| IQ1/IQ2 | Large Diaphragm /High-temperature Pressure Transmitter | | |
| Measurement Range | -0.1. . .0~0.01...100MPa |
| (0-X)Kpa or MPa | X: Indicates the Actual Measuring Range |
| Code | Power Supply |
| D1 | 24VDC |
| D2 | 5VDC |
| D3 | Other |
| Code | Output Signal |
| S1 | 4~20mADC | S5 | 0~20mADC |
| S2 | 1~5VDC | S6 | 0~10VDC |
| S3 | 0~5VDC | S7 | 0.5~4.5VDC |
| S4 | 0~10mADC | | |
| Code | Pressure Connection |
| J1 | M20×1.5 |
| J2 | G1/2 |
| J3 | G1/4 |
| J4 | 7/16-20UNF |
| J5 | Other |
| Code | Electrical Connection |
| B1 | Hirschmann |
| B2 | PG7 Plug |
| B3 | Sealed Cable Output |
| B4 | 2088 Industrial Casing |
| B5 | 2088 Industrial Casing with Display |
| B6 | Other |
| Code | Pressure Type |
| G | Gauge Pressure |
| A | Absolute Pressure |
| S | Sealed Reference Pressure |
FAQ:
1. Q: What are the features of your pressure sensor transmitters?
A: High precision, durability, and excellent performance.
Customization available.
2. Q: Can I customize special specifications?
A: Yes, our engineers can tailor products to meet specific needs. We provide OEM and ODM service.
3. Q: What is your production capacity?
A: Our manufacturing facilities can produce up to 30,000 pressure
sensor transmitters per month, so we are fully capable of meeting
the needs of large-scale orders. However, it is advisable to
contact our sales team in advance to ensure smooth production and
delivery scheduling.
4. Q: What's the typical delivery period?
A: 5~8 working day for standard models. Customized products may
vary.
