BPHT24-III pressure transmitter
Introduction of Flush Diaphragm Pressure Sensor :
BPHT24-III pressure transmitter The signal processing circuit is located inside a stainless steel
housing, converting the sensor signal into a standard output signal. This pressure
transmitter is primarily used in places where high sanitary conditions are required,
ensuring reliable and accurate pressure measurements in hygienic environments.
Product Features:
- Various pressure interface options
- Designed for hygienic applications to prevent medium scaling
- High accuracy with a fully stainless steel structure
- Easy to clean.
Applications:- Suitable for measuring non-corrosive gases and liquids with 316L
- Ideal for environmental protection and chemical industries
- Used in the marine and aviation industries
- Well-suited for use in the medical, biopharmaceutical, and food
hygiene industries.
Performance Parameters: |
| Measurement Range | 0~35Kpa…~20MPa |
| Pressure Type | Gauge Pressure, Absolute Pressure, Sealed Pressure |
| Overload | ≤ 1.5 times of the rated range |
| Accuracy @ 25℃ | ±0.25% (Typical) ±0.5% (Maximum) |
| Repeatability& Hysteresis | 0.02%F.S(Typ.) 0.05%F.S(Max.) |
| Long-Term Stability | ±0.1%F.S/Year(Typ.) ±0.2%F.S/Year(Max.) |
| Zero Point Temperature Drift | ±0.02%F.S/℃(≤100KPa) ±0.01%F.S/℃(＞100KPa) |
| Full Scale Temperature Drift | ±0.02%F.S/℃(≤100KPa) ±0.01%F.S/℃(＞100KPa) |
| Frequency Response | 2.4Khz |
| Compensation Temperature | 0-70℃(≤10mpa,customizable) |
| Operating Temperature | -20℃~80℃ |
| Storage Temperature | -40℃~120℃ |
| Vibration | 10g,55Hz ～ 2kHz |
| Housing Material | 304,316L |
| Diaphragm Material | 316L |
| Insulation Resistance | 100MΩ 100VDC |
| Explosion-proof Rating | Ex db IIC T6 Gb |
| Protection Rating | IP65 |
| O-Ring Seal | Fluoro rubber |
| Weight | ~0.8kg |
| Output Signal | Supply Voltage | Output Type |
| 4～20mA | 12～30VDC | 2/3/4 wire |
| 0～10/20mA |
3 wire |
| 0/1～5V |
| 0/1～10V |
| 0.5～4.5V | 5VDC |
| RS485 Communication Protocol | 3.6～30V / Battery | 4 wire |
1. Should try to avoid installation in vibration, impact or high
temperature environment, so as not to affect the accuracy of the
measurement and the life of the equipment,
2. Keep the environment around the pressure transmitter clean,
avoid dust, grease and other impurities into the equipment,
affecting its normal operation;
3. Avoid pressure exceeding the rated range of the pressure
transmitter to avoid damage to the equipment. If it is necessary to
measure the pressure beyond the rated range, the pressure
transmitter with the appropriate rated range should be selected;
4. Select the appropriate material according to the characteristics
of the measured medium to prevent the corrosive effect of the
medium on the pressure transmitter. In order to ensure the accuracy
of the measurement,
5. It is recommended to calibrate the pressure transmitter
regularly. The calibration period can be determined according to
the use environment and requirements.
| Order Guide |
| BP93420XX | Pressure Transmitter |
| Code | Outline Construction |
| IX | Display Pressure Transmitter | IIC/III | Industrial General/ Display Pressure Transmitter |
| Measurement Range | 0~35Kpa…~20MPa |
| (0-X)Kpa or MPa | X: Indicates the Actual Measuring Range |
| Code | Power Supply |
| D1 | 24VDC |
| D3 | Other |
| Code | Output Signal |
| S1 | 4~20mADC | | |
| S2 | 1~5VDC | S6 | 0~10VDC |
| Code | Pressure Connection |
| J1 | M20×1.5 |
| J2 | G1/2 |
| J3 | 1/2NPT |
| Code | Electrical Connection |
| B1 | Hirschmann |
| B2 | PG7 Plug |
| B3 | Sealed Cable Output |
| B4 | 2088 Industrial Casing |
| B5 | 2088 Industrial Casing with Display |
| B6 | Other |
| Code | Pressure Type |
| G | Gauge Pressure |
| A | Absolute Pressure |
| S | Sealed Reference Pressure |
