Features of Ultrasonic transducer
1. Compatible with the many kinds of this similar product.
2. High sensitivity
3. Readings can occur up to every 33mS(30Hz) within 3meters or
occur up to every 80ms(12.5Hz) within 10meters.
4. Free run operation can continually measure and output ranger
information
5. 9V-28V supply with very low average current draw
6. Multi-kind output type such as analog (40-20mA, 0/1-5V,
0/1-10V), RS485, Can bus.
7. Sensor operates at 40 KHz, 112 KHz, 175 KHz, 300 KHz, 1 MHz
Brief introduction of Ultrasonic transducer
This sensor provides very short to long-range detection and
ranging, in a compact, robust PVC or stainless steel housing,
designed to meet IP67 water intrusion. The power 9.0V-28V operation
detects objects from 0.1meters to 10meters and provides sonar range
information from 0.25meters out to 10meters out with 0.001meters or
0.01meters resolution. The interface output formats included are
pulse width output, analog voltage output 0/4-20mA current output,
NPN/PNP output and RS485,RS232 output modbus-RTU and modbus-ASCII
supported.
Parameters |
General Specifications |
Sensing distance 100.4000mm |
Adjustment range 100.4000mm |
Unusable area 0.200mm |
Standard target plate 100mm×100mm |
Transducer frequency About 112kHz |
Response delay About 195ms |
Indicators/Operating means |
LED blue Power on |
LED yellow Indication of the switching state Flashing: program function object detected |
LED red permanently red: Error Red,
Flashing: program function,object not detected |
Electrical specifications |
Operating voltage UB 10.30VDC,ripple10%ss |
Power consumption P0 ≤900 mW |
Output |
Output type analogue output 0.10V |
Resolution evaluation range [mm]/4000, but ≥ 0.35 mm |
Deviation of the characteristic curve ≤0.2% of full-scale value |
Repeat accuracy ≤0.1% of full-scale value |
Load impedance 0.500 Ohm |
Temperature influence ≤2% from full-scale value |
Ambient conditions |
Ambient temperature -25.70°C |
Storage temperature -40.85°C |
Mechanical specifications |
Protection grade IP67 |
Connection Connector M12x1,4-PIN |
Material Housing Brass, nickel-plated |
Transducer Epoxy resin/hollow glass sphere mixture; Polyurethane foam |
Weight 60g |
External synchronization
The sensor can be synchronized by the external application of a
square wave voltage. A synchronization pulse at the synchronization
input starts a measuring cycle. The pulse must have a duration
greater than 100 μs. The measuring cycle starts with the falling
edge of a synchronization pulse. A low level > 1 s or an open
synchronization input will result in the normal operation of the
sensor. A high level at the synchronization input disables the
sensor. Two operating modes are available:
1. Multiple sensors can be controlled by the same synchronization
signal. The sensors are synchronized.
2. The synchronization pulses are sent cyclically to individual
sensors. The sensors operate in multiplex mode.
Internal synchronization
The synchronization connections of up to 5 sensors capable of
internal synchronization are connected to one another. When power
is applied, these sensors will operate in multiplex mode.
The response delay increases according to the number of sensors to
be synchronized. Synchronization cannot be performed during
TEACH-IN and vice versa. The sensors must be operated in an
unsynchronized manner to teach the evaluation limits.
Note:
If the option for synchronization is not used, the synchronization
input has to be connected to ground (0V) or the sensor has to be
operated via a V1 cable connector (4-pin).
Adjusting the evaluation limits
The ultrasonic sensor features an analogue output with two
teachable evaluation limits. These are set by applying the supply
voltage - UB or + UBto the TEACH-IN input. The supply voltage must be applied to the
TEACH-IN input for at least 1 s. LEDs indicate whether the sensor
has recognized the target during the TEACH-IN procedure. The lower
evaluation limit A1 is taught with - UB, A2 with + UB.
Two different output functions can be set:
1. Analogue value increases with rising distance to object (rising
ramp)
2. Analogue value falls with rising distance to object (falling
ramp)
Evaluation limits may only be specified within the first 5 minutes
after
Power on. To modify the evaluation limits later,
the user may specify the desired values only after a new Power On.
TEACH-IN rising ramp (A2 > A1)
- Position object at lower evaluation limit
- TEACH-IN lower limit A1 with - UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A2 with + UB
TEACH-IN falling ramp (A1 > A2):
- Position object at lower evaluation limit
- TEACH-IN lower limit A2 with + UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A1 with - UB
Default setting
A1: unusable area
A2: nominal sensing range
Mode of operation: rising ramp
Adjusting the sound cone characteristics of Small waterproof Ultrasonic transducer
The ultrasonic sensor enables two different shapes of the sound
cone, a wide angle sound cone and a small angle sound cone.
1. Small angle sound cone
- switch off the power supply
- connect the Teach-input wire to -UB
- switch on the power supply
- the red LED flashes once with a pause before the next.
- yellow LED: permanently on: indicates the presence of an object
or disturbing object within the sensing range
- disconnect the Teach-input wire from -UB and the changing is
saved
2. Wide angle sound cone
- switch off the power supply
- connect the Teach-input wire with + UB
- switch on the power supply
- the red LED double-flashes with a long pause before the next.
- yellow LED: permanently on: indicates an object or disturbing
object within the sensing range
- disconnect the Teach-input wire from + UB and the changing is
saved
Installation conditions
If the sensor is installed at the environment temperature fall
below 0°C,It should do well on the protective measures. In case of
direct mounting of the sensor in a through hole using the steel
nuts, it has to be fixed at the middle of the housing thread.
The quality principle: Quality is the best sales |
|
Payment :We accept T/T, PayPal, Western Union, MoneyGram , Escrow |
|
Shipping: |
1.All parts will be shipped out within 1 - 3 working days after
comfirm the payment |
2. DHL / FEDEX / UPS / EMS / TNT / China Post /Aramex |
3.We are not responsible for force majeure accidents, delays or other
issues, like the shipping service. |
After-sales service
We promise to deliver the following after-sales service:
1. Warranty: The warranty period is 12 months starting from the
shipping date;
2. Customers will enjoy free repair services for failures found
within the warranty due to manufacturing quality;
3. We provide paid repair services for meter damages not arising
from manufacturing quality issues or meter damages not within the
scope of warranty.
