Med-tronic LP20 LP20E Defibrillator Recoder Printer MODEL XL50 PN 600-23003-09 MPCC PN 3200920-000

Med-tronic LP20 LP20E Defibrillator Recoder Printer MODEL XL50 PN 600-23003-09 MPCC PN 3200920-000

Printer Module Installation

Warning

Possible blows and damage to equipment. Follow the removal procedure carefully to avoid bumping or damaging the cable during removal.

Note: If you installed only the A12 printer, start with step 9. Follow these steps to install the printer module:

1. Slide the W14 printer flex cable under the W06ECG cable and guide the printer cable along the right side of the holder.

2. Connect the printer cable connector and the 4-pin power cable connector to the large connectors on the monitor.

3.Insert the 2.4 pin plug into the small hole on the shield.

4. Connect the 4-pin power plug to the A03 power module of the J45 and ensure that the plug is seated properly.

5. Place the printer shield (89) in the base box.

6. Install three new 4-40 x 0.312 (173) screws at the bottom of the printer cover.

7. Once removed, press the clip (225) on the printer cover to secure the J45 pigtail.

8. Install the printer panel (83) and make sure it is flush with the bottom.

9. Connect the W14 printer cable to the J1 connector on the printer. The cable should lie flat against the back of the printer.

10. Ensure that the W14 printer flex cable is between the two clamped screws.

11. Slide the A12 printer into the printer cover.

12. Tighten the two clipped screws on the A12 printer.

13. Attach the paper roll to the A12 printer and close the printer cover. 14. Install the plate pack.

14. Install the front cover.

15. Install the top case.

16. Install the A07 battery.

18. Complete Picture in Picture

LIFEPAK 20/20e Defibrillator/Monitor Interconnect Diagram

Printer Module Removal

WARNING! Possible shock and damage to the device. The cable can be pinched and damaged during disassembly. To avoid the cable getting caught, follow the removal instructions. To remove the A12 printer unit:

Note: Before disassembly, remove the following parts: - A07 battery - Top case - Front case - Stand for boards

1. Open the printer door and remove the roll of paper from the printer.

2. Loosen the two screws attached to the back wall inside the printer.

3. Pull the printer A12 carefully out of the printer compartment (89).

4. Disconnect the printer's W14 flexible cable from the printer to the printer's J1 connector.

Note: If you delete the A12 printer, the deletion process will be complete. If you are removing the printer cover or the W14 printer flex cable, continue with the removal process until the desired part is removed.

5. Slide the edge of the printer (83) up and out of the bottom of the housing.

6. Remove and remove three 4-40 × 0.312 Screws (173) from the bottom of the printer housing (89).

7. Carefully lift the cover to access the 4-pin power cord.

8. Disconnect the 4-pin power cable from power module A03 on J45 and insert it into the small slot in the housing.

9. Thread the 4-pin power cord and flex from the W14 printer through the widest part of the box.

10. Remove the printer housing (89) from the lower housing.

11. Pick up the W06 EKG cable and carefully remove the W14 printer flex cable from the lower compartment. The cable is attached with glue, so remove it evenly to avoid damage to the connector or cable.

Observed Symptom

Not printing

Suggested Corrective Action

Perform printer test.

Check for proper paper.

Check for 3.3 V on pins 14 and 16 on the J38 test connector on the A05 UI PCB.

■ If either is higher than 3.3 V, replace the W14 Printer Flex Cable. ■ If both are lower than 3.3 V:

– Check or replace the A12 Printer Assembly.

– Replace the A05 UI PCB

Light print

Verify use of proper paper.

Check the W14 Printer Flex Cable connection.

Check or replace the A05 UI PCB.

Missing or broken characters

Verify use of proper paper. Clean the printhead. Check or replace the A12 Printer Assembly

China World Technology Medical Equipment Service Group is a company engaged in medical equipments/repair parts and accessories products trading company. The company was established in September 2005, has many famous enterprises at home and abroad (such as America USCO company) to establish a long-term friendly business relationship. Company mainly engaged in patient monitor and other medical machine products. Since its inception continue to absorb a variety of talents, improve product quality, improving staff quality, in order to grow their companies. Strict quality guarantee system and perfect management system, high-quality products after-sales service is our foothold in this, my company of "quality first, reputation first" principle, provide customers with quality and quantity of various types of products. Always uPHiliphold the "quality, integrity and pragmatic, motivated, service-oriented" business PHiliphilosoPHiliphy, and applies the company's management and operating among. The face of fierce competition, the company system is constantly being improved, relying on science and technology, continuously improve the technology content of products sold, for society, customers and companies to create a higher market value. Our company has been in good faith to create enterprises, to credit management market, has won a good reputation, also won the respect of their domestic counterparts.
Business strictly in accordance with relevant state laws, regulations and rules of the WTO requirements management according to law, actively participate in regional economic.Business prospects and good, the next time, our company will expand the scale of operation and steady development of corporate economic, sincerely seeking partners, good faith cooperation and seek common development, writing a new chapter in medical equipment field.