EtherCAT/Canopen Bus Type Servo Amplifier Controller For Cardboard
Cap Feeder
EtherCAT/Canopen Bus Type Servo Amplifier
AC Power 380V 4.5KW
Three phase with 17/23bit Tamagawa absolute encoder;
Modbus/CANopen/EtherCAT Commucation Protocol Type
Products Description
| Products | AC Servo Drive Controller For Cardboard Cap Feeder |
| Brand | Vector |
| Model No. | VVEC-VC-01233HC-M-E/180MB-4R520A33F-MF2 |
| Power | 4.5KW |
| Voltage | 380V |
| Phase | Three Phase |
| Rated Speed | 2000 rpm |
| Rated Current | 9.5A |
| Rated Torgue | 21.5N.m |
| Communication Protocols | Modbus/CANopen/EtherCAT |
| Key Name | Key function |
| Mode | mode switch, return to the previous menu |
| ▲(add) | increase flashing bit value of the LED digital tube |
| ▼(dec) | Decrease flashing digit value of the LED digital tube |
| ◄◄(shift) | Moves the blinking LED tube to the left; checks the high value of
data
longer than 5 bits; Fault reset;execute Fn function |
| SET | read/write parameter values |
Installation:
● Install the driver on a dry and sturdy platform. Maintain good
ventilation and
heat dissipation during installation and maintain good grounding.
● Please install in the specified direction to avoid malfunction.
● When installing, please ensure that the servo driver is kept at a
specified
distance from the inner surface of the cabinet and other machines,
otherwise it may cause fire or malfunction.
Installation
Environment
Requirements | Atmospheric Pressure | 86~106kPa |
| Mbient Humidity | 0~55℃ |
| Ambient Temperature | 0~90%RH |
| IP Rating | IP20 |
| Vibration | 0~4.9m/s^2 |
● When installing, do not block the suction and exhaust ports, and
do not allow foreign objects inside the product
to enter, otherwise it may cause malfunction or fire due to aging
of internal components.
● Do not place heavy objects on or under this product as this may
result in injury.
● Please install in the following environment:
1.places without direct sunlight;
2.Locations where the ambient temperature is in the range of 0 ° C
to 55 ° C;
3.Relative humidity in the range of 0% to 95%, and no condensation;
4.Locations free of water droplets, vapors, dust and oily dust;
5.Locations where there is no high heat device;
6.Non-corrosive, flammable gas and liquid sites;
7.It is not easy to splash water, oil and medicine;
8.places that are not exposed to radioactive radiation;
9.Strong and vibration-free places;
10.Locations where there is no electromagnetic noise interference.
Wiring precautions
● It is recommended not to use single-phase 220V for main power
supply,
which may cause damage to electrolytic capacitor due to lack of
phase.
● Do not change the wiring during power-on, otherwise it may cause
electric shock or injury.
● Please perform wiring or inspection by professional technicians,
otherwise it
may cause electric shock or product failure.
● Please carefully confirm the wiring and power supply. The output
circuit
may be short-circuited due to wiring errors or application of
different voltages. The brake does not operate
when the above fault occurs, which may result in mechanical damage
or personal injury.
● Do not connect the input power cable to the U, V, and W terminals
of the
drive. Otherwise, the servo driver will be damaged.
● When wiring, do not pass the power cable and signal cable through
the same pipe, and do not bundle them
together. The distance between the two should be more than 30cm to
avoid interference.
● The driver ground terminal must be grounded to avoid leakage and
reduce the interference of the system,
and the diameter of the ground wire should be the same as or above
the power supply line.
● When connecting the AC power supply and DC power supply to the
servo unit, connect to the specified terminal.
Failure to do so may result in malfunction or fire.
● For the wiring length, the command input line is up to 3m and the
encoder line is up to 20m.
● Use a twisted-pair shielded cable for the signal cable and
encoder cable, and ground the shield with a single end.
●The U, V, W terminals of the driver and the U, V, and W terminals
of themotor should be connected one by one
according to the name. If it is wrong connected, the motor cannot
operate normally.
● Common DC bus products require pressure sensitive resistors and
the wiring is secure.
● Please check the power after the power is off for at least 5
minutes. Even if
the power is turned off, high voltage may remain inside the servo
drive. Therefore, do not touch the power terminal
within 5 minutes after the power is turned off, otherwise it may
cause electric shock.
● Do not turn the power ON/OFF frequently. When it is necessary to
continuously turn ON/OFF the power, please
control it once or less in 1 minute. Since the power supply section
of the servo driver has a capacitor, a large charging
current (charge time of 0.2 seconds) flows during the ON/OFF power
supply. Therefore, if the power is turned ON/OFF
frequently, the performance of the main circuit components inside
the servo driver will be degraded.
● Do not apply power when the terminal block screws are loose or
the cable is loose. Otherwise, it may cause fire.
● Take appropriate shielding measures in the following locations,
otherwise the machine may be damaged:
1. Locations that cause interference due to static electricity;
2. A place that produces a strong electric field or a strong
magnetic field;
3. Locations where there may be radiation radiation;
4. A place with a power cord nearby.
Accessories:
| Accessory name | Image | |
| Satandard Spare Parts | Power terminal |  | Adapt to E1,E2 structure drive |
| Cn3 encoder plug | Encoder plug on the driver side |
| Cn4 control terminal plug | Input/output signal terminals,user wiring |
| Encoder connection line | The standard cable length is 3, 5, 8, 10, 13, 15 meters, according
to customer
needs Provide independent connector |
| Power line | The standard cable length is 3, 5, 8, 10, 13, 15 meters, according
to customer
needs Provide independent connector |
| Drive monitoring line | Connect and adjust the software for remote monitoring and firmware
update |
| Purchasing Spare Parts | USB to RS232 Adapter cable | If necessary, self purchase |
| Ethernet communication line | If necessary, self purchase |
Packing:
| Packing details of Servo Drive |
| Products | E1(3-6A) | E2(7-12A) | E3(16-27A) | C015(32-38A) | C022(45-60A) |
| Ctn. Size | 280*208*78 | 280*208*112 | 375*290*155 | 440*296*288 | 510*305*325 |
| Packing details of Motion Controller |
| Products | VA Motion | VA Expansion | VE Motion | VE Expansion(32) | VE Expansion(76) |
| Ctn. Size | 176*165*78 | 127*75*70 | 144*128*69 | 176*164*78 | 316*164*78 |
Delivery Time and Shipping Way
| Quantity | 1-5 kits | 50-100 kits | 200-500 kits |
| Delivery time | Within 3 days | 5-10 days | 15-25 days |
1. For small order we always can delivery out within 1 week.
2. Our products can be shippied via Air, Land or Sea.
Cetificates:
1. CE (EU Safety Standard);
2. IEC/EN61800-5-1:2007 (Safety requirements for electrical,
thermal and energy in Section 5-1 of the
variable speed electric driver system), corresponding to the
national standard GB12668.501-2013;
3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system
part 3 electromagnetic compatibility
standards and its specific test methods), corresponding to the
national standard GB12668.3-2012.
Our Team
