SCG353A044 SCDUG353A044 Right Angle 1'' Inch Pulse Jet Valve
ASCO Type 353 Series high flow die-casting aluminum bodies,
Integral compression fittings for fast, easy, secure installation.
It's specially designed for reverse jet type dust collector
systems. Quick mount connection eliminates thread cutting and
sealing. Valves may be mounted in any position. The concept of
pulse -jet dust collection system is basic: dirty air goes in, dust
or particulate gets removed, and clean air comes out.
Solenoid valve sealing material
EPDM rubber
The most important feature of EPDM is its superior resistance to
oxidation, ozone and erosion. Since EPDM is a polyolefin family, it
has excellent vulcanization characteristics. Among all rubbers,
EPDM has the lowest specific gravity. It absorbs a large amount of
fillers and oils and has little effect on properties. Therefore, it
is possible to produce a rubber compound which is inexpensive.
Characteristics
1. Low density and high filling;
2, aging resistance;
3. Corrosion resistance;
4, water vapor resistance;
5, resistance to hot water performance;
6, electrical performance;
7, flexibility;
8, adhesion.
YOUTUBE video of SCG353A044 Pulse Jet Valve:
Technical Data:
| Model No | SCG353A044 |
| Port Size | G1 Inch |
| Working Pressure | 0.3~0.8Mpa |
| Working Temperature | -5~+55℃ |
| Working Medium | Air |
| Relative Humidity | ≤85% |
| Protection Class | IP65 |
| Service Life | Over 1000000 times |
| Voltage | AC220V, AC110V, AC24V, DC24V |
| Special voltages and specifications , please contant us. |
Dimension of SCG353A044 Pulse Valve and Pulse Valve Repair Kit :
Model No. | BB11036001 |
Ref No. | 400325 |
Voltage | AC24V, AC110V, AC220V, DC12V, DC24V |
Connection | DIN 43650A |
Other can be customized, please contact us. |
Model No. | BAPC211037301 |
Ref No. | C113444 |
NC/NO | NC |
2 Way or 3 Way | 2Way |
Other can be customized, please contact us. |
Model No. | A044 |
Ref No. | C113444 |
Replace For | SCG353A044 |
Mounting Hole Dia. | 6.5mm |
Sealing Disc OD | / |
Ref. Number | SCG353A044 |
Working Pressure | 0.3~0.8Mpa |
Voltage | 24V DC, 110V AC, 220V AC
Other voltages can be customized. |
Diaphragm Nos | 1 |
Port Size | G1'' |
Other requirement please contact. |
Details About Integral Pilot Operated Pulse Valve:
How Pulse Jet Dust Collector System Working :
Dirty air containing particles of dust enters the collector through
the ductwork. Fans either push or pull the air through the ducts.
The air hits a set of baffles, which are angled pieces of metal
that slow it down. As a result, this keeps the dust from hitting
the filters at full speed.
Then the air enters what we call the dirty air plenum. This just
means the side of the collector where the air is dirty. At the
bottom of this space, collected dust drops out into a drum or
hopper.
Next, the air passes through the dust collector’s cartridge
filters. In the dust collector system , these hang vertically from
the tube sheet, which is the metal sheet separating the dirty and
clean air spaces.
Pleating the filters give them more surface area. filters are also
coated with a nanofiber material. This makes the spaces that the
air must go through smaller.
The filters capture the dust. Some of it falls off. Some of it
sticks to the filters. Gaskets at the top of each filter seal it to
the tube sheet to keep dust from sneaking through.
A pulse of compressed air blows into the filters. Because the pulse
of compressed air goes in the reverse direction of the regular
airflow, we call it a reverse pulse-jet collector.
The pulse of compressed air blows the accumulated dust off the
filters. The dust drops out of the collector and the filters are
ready to collect more dust.
On the other side of the filters, filtered air enters the clean air
plenum. From there, it can go back into the facility or vented
outside.
Construction:
Body and Dreeser Nuts: Aluminum (diecast)
Ferrule: 305 Stainless Steel
Armature: 430FR Stainless Steel
Diaphragm and Seals: Nitrile or FKM
Spring: 304 Stainless Steel
Screws: 302 or 304 Stainless steel
Diaphragm Seat: PA-66 (25 & 40MM standard), Nitrile-coated mild
steel (76MM standard), Acetal (102MM standard) or FKM coated mild
steel
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
