FS 120-12 CI 1/4 NPT Air Spring Contitech Replaces By Goodyear 1B8-560 Air Actuator

FS 120-12 CI 1/4 NPT Contitech Air Spring Replaces by Goodyear 1B8-560 Air Actuator

Goodyear ​1B8-560 Technical parameters Replaces FS 120-12 CI 1/4 NPT Contitech

❶Nut/blind nut

Top plate screw (nut) teeth: 2 x 3 / 8-16UNC
The screw center distance of the top cover plate: 70 mm
Screw (nut) teeth of the bottom cover plate: 2 x 3 / 8-16UNC
The screw center distance of the bottom cover plate: 70 mm

❷Air hole/air inlet/air fittings
Air hole/air inlet: 1 / 4-18NPTF
The screw center distance between the air hole and the nut: 35 mm

❸Cover plate
Top plate diameter: 135 mm
Diameter of the bottom cover: 135 mm

Bell rubber bellows
Maximum diameter of rubber bellows: 240 mm
Natural diameter of rubber bellows: 225 mm
Working stroke: minimum 60 mm to maximum 180 mm
Maximum height: 180 mm
Minimum height: 50 mm
Stroke height: 120mm

❺Bumper block/bumper block
No bumper block

❻Belt loop/Belt loop
With belt loop: not a belt loop

Durability of Goodyear air spring

Goodyear Air Spring ​1B8-560, without internal rod, piston or sliding seal
In Goodyear's 1B8-560 actuator, there is no internal rod, piston or sliding seal like many traditional cylinders. The advantage in Goodyear's application is that dust or grit will corrode traditional cylinder seals. This gives Goodyear an advantage.
Goodyear air spring angle capability
If there is no U-clamp, the stroke through the arc may produce an angular movement of up to 30 degrees.
Goodyear air spring side load
In some cases, free-stroke actuators are not affected by side loads. This eliminates the possibility of rod bends, nicks and excessive seal wear that are common when using traditional cylinders.
Goodyear air spring ​1B8-560 friction reduction
In the absence of a sliding seal, the Goodyear actuator ​1B8-560 will not break away from friction.
Goodyear Air Spring ​1B8-560 can be used flexibly
The free-stroke actuator can be used with a variety of media (liquid or gas) (Please refer to the data sheet for acceptable media selection.)

Note:

• The restoring force is required to compress the air spring cushion to the minimum height. Usually achieved by applying external force

• The entire air spring cushion surface of the upper and lower plates must be used to absorb the force

• The air spring cushion can only move on the workpiece, or it must be equipped with a limit stop at the end of the stroke, otherwise the rubber material of the air spring cushion will be overloaded or cause internal damage

•Before removing the air spring cushion, the air pressure in it must be discharged.

• During the operation, the wall of the air spring cushion must not be in contact with other parts, otherwise the air spring cushion will be worn and damaged, and air leakage will occur.

Guangzhou Guomat Air Spring Co., Ltd. is located in Guangzhou, about 15min’s drive from Baiyun Airport. Our mainly products are air spring, rubber bellows, air suspension spring, air suspension compressor and refitted suspension system. They are widely used in bus, truck, cabin, vehicles’ seat, luxurious car and industrial machine field.

GUOMAT Factory gate：

Established in 2008, Our company covers 20,000㎡ and is located in Taihe Town Baiyun District. With the rapid development of our company, we are equipped with modernized workshop and advanced rubber air springs equipments now. We are the first company who started air spring business and has become one of the largest air spring manufacturing bases in China.

In 2017, we launched a collaboration with High Tech of US customers to customize the products of our customers and the logo of our customers. Every year, there are about 10,000 orders. In continuous cooperation, the products meet the international inspection standard ISO/TS16949:2009, and the customers are very satisfied with the products produced. This is our high recognition from American customers and also gives us Great motivation.

In 2018, we started cooperation with German GmbH, mainly industrial air springs, which are suitable for industrial equipment. We have successfully developed and produced the natural air-seal of the skin to reach the 700mm flanged air spring, the customer's annual demand is a few hundred.

With the development of business and demand for customers, our company introduced business with TomLog Corporation in 2010, our strategic cooperative partner in Taiwan. Then we developed air compressor program and air spring related business, in 2015, America Goodyear Corporation met with the transfer of shares in the North American plant, our company was granted with sale agent for air springs in China, providing more choice for our customers. Our company adopts the most advanced domestic air spring processing equipment and international production technology. Combined with unique production process, our company strictly execute international standards for production and spare no efforts to create the world-class products. We will endeavor to make air spring widely used at home and abroad, and let more and more customers to enjoy the best damping effect.