Horizontal Glass washing and drying machine processing size can be
customized the max size can reach to 2600mm
LJWBQJ-2500A Glass Washing Machine as first step for glass processing
Name application
Glass washing machine used for cleaning and drying the upper and
lower surfaces of ordinary plate glass and high quality low-e
glass,it is composed of incoming segment, cleaning air-drying
segment and outgoing segment.
The machine for washing and also drying of glass products, performs
automatic washing of products from two sides at the same time, via
the upper and lower brushes. The equipment must perform the
following operations:
- Glass loading (Automatic from the processing line);
- Glass washing (Automatic);
- Glass drying (Automatic);
- Unloading (Manual).
- Requirements for compressed air.
Pressure – 6 bar.
Pressure-4 bar.
Water tank details►
The washing part in contact with water is made of stainless steel
Air knives detail ►
Two pairs of special stainless steel aluminum alloy air knife
configuration, strong wind, good air drying effect, with heating
system(with temperature control device, optional opening and
closing)
High quanlity profile detail►
Aluminum alloy assembled structure, no scrap concept, permanent
use,high efficiency, energy saving 70% efficiency
The fan detail►
The fan is equipped with air filter in the air inlet chamber, with
large air volume and good air drying effect,The whole fan box is
installed in the upper part of the workshop, with the air filter
screen on the side for easy inspection and cleaning
Technical parameters:
1. Maximum glass width: 2500mm (effective maximum: 2650mm)
2. Minimum glass specification: 400mm×400mm (limited to single row
on left and right sides)
3. Glass thickness: 3mm-25mm (digital display)
4. Speed range: glass thickness within 3-25mm Vmax=1-12m/min
5. Main drive, brush speed regulation method: frequency control
6. Table height :900±25mm
| Maximum glass width | 2500mm (effective maximum: 2650mm) |
| Minimum glass specification | 400mm×400mm (limited to single row on left and right sides) |
| Glass thickness | 3mm-25mm (digital display) |
| Speed range | glass thickness within 3-25mm Vmax=1-12m/min |
| Main drive, brush speed regulation method | frequency control |
| Table height | 900±25mm |
| Total power | 42KW(water-bearing wind heating: 15KW) |
| Water source | self-circulation, tap water (according to civil water standards)
and deionized water water supplement (deionized water equipment
shall be provided by the buyer) |
| Power source | 380V 50Hz |
| Dimensions (length × width × height) | approximately 6260*4800*3100 |
| Weight | 3940kg |
Vacuum glass electric suction cup lifter KX4
Manual rotation: 360° edgewise, with locking at each quarter point.
Manual tilt: 90° between upright and flat, with automatic latching
in upright position.
Product Features
1. The vacuum glass lifter is for handling the glass sheet.
2. Glass lifter max. carrying capacity 200kg. 400kg. 600kg.800kg (
a safety factor 4.0 include).
3. The vacuum pump, valve, switch and some important spare parts we
are import from oversea.
4. Stable performance, easy to maintain, efficient, safe, quick,
easy.
5. The material of suction pad is NBR (oil resistance,skid
resistance, corrosion resistance) , Be able to effectively and
steel vacuum suction and produce vacuum.
6. The suction pad can be adjustable, can be turned off and open
individually.
7. The vacuum lifter is equipped with a buzzer and warning light
units, in case of a power failure or vacuum leakage, an optical and
an acoustic signal goes off immediately to warn the operator to do
emergency operation.
8. The vacuum lifter is equipped with safety tank&Pressure
switch warning, when the power is turned off in sudden, always can
keep the work piece not falling down for 30 minutes.
9. The design of vacuum lifter by our company is passed to EU CE
passed.It is CE identification product.
