2000KG/M3 Bale Density Turn Over Out Hydraulic Scrap Baler
Introduction of scrap hydraulic baler
Metal baling machine can extrude all kinds of metal wastes (scrap,
shaving, scrap steel, scrap aluminum, scrap copper, scrap stainless
steel, scrap car, etc.) into qualified charges of cuboid,
octagonal, cylinder and other shapes, which can not only reduce the
transportation and smelting costs, but also improve the charging
speed. This series of balers are mainly used in steel plant,
recycling industry, nonferrous metal and ferrous metal smelting
industry.
Technical datas of scrap hydraulic baler
| Model | 2500 |
| Main pressure | 2500KN |
| Motor Power | 2*22kw |
| Pump | 160YCY14-1B |
| Material box | 2.0*1.5*1.0mm |
| Bale size | 500*500mm |
| Bale-out | Turn over / manual |
| Bale density | ≥2200kg/m3 |
| Production efficiency | 60-80 ton / day |
Features of scrap hydraulic baler
1) Hydraulic drive is used in this machine, having reasonable
design, compact structure and reliable sealing performance.
2) Super bin design with large one-time feeding and high working
efficiency.
3) Where there is no power supply, diesel engine can be used as power.
4) 100 degree turnover type bale discharging form, having clear,
ordered and beautiful corner angle.
Note: the size of material box and bale can be customized according
to the actual needs of customers
Structure of scrap hydraulic baler
1. Main machine is composed of frame, door cover and cover
cylinder, main cylinder and main pressure head, side cylinder and
side pressure head, bale turning cylinder and bale turning machine
etc.
1) Frame is composed of base, right and left wall plates, cover
plate, main cylinder bracket, side cylinder frame etc. Compressed
bin is composed of base, right and left wall plates, door cover,
main pressure head, side pressure head and panel turnover etc.,
each part (except panel turnover) is installed with abrasion
resistant lining board through carburizing and quenching.
2) Door cover and cover cylinder. Door cover should be hinge
jointed with spindle sleeve on right and left wall plates, cover
cylinder should also be hinge jointed with beam support by pin,
slipper of door cover (tapered end should be installed at front
end) should be connected with piston rod head of cover cylinder,
under movement of cover cylinder, close and open of door cover are
finished, at this time, it takes effect of tight locking and loose
locking.
3) Main cylinder and main pressure head. Main cylinder should be
installed at lower side part of cover cylinder support, main
pressure head should be connected with piston rod of main cylinder
with screw, under the advance and retreat effect of main cylinder,
impaction and return action of bale block are finished.
4) Side cylinder and side pressure head. Side cylinder should be
installed at lower side part of cover cylinder support, side
pressure head should be connected with piston rod of side cylinder
with screw, under the advance and retreat effect of side cylinder,
precompression and return action of bale block are finished.
5) Bale turning cylinder and bale turning mechanism. Bale turning
cylinder and bale turning mechanism should be installed in opposite
to the main cylinder, turnover and reset action of bale block are
finished by advance and retreat of bale turning cylinder.
6) All main cylinder, side cylinder, cover cylinder and bale
turning cylinder are of single piston rod double acting cylinder,
there is a piston inside cylinder which is installed with sealing
component, it makes the cylinder body form front and rear oil
chambers. When high-pressure oil acts on front chamber (rear
chamber), piston will be pushed and made advance movement (return
movement). Cylinder port is designed with a guide sleeve that is
used for supporting guides and sealing of piston rod.
2. Hydraulic system is composed of motor pump station, valve
station, oil tank and pipeline etc.
3. Electric system is mainly composed of motor start circuit etc.
