High Quality BLDC Hall Sensor Motor Cotroller 110/220VAC Input
Continuous Current 2-12A
Model No. BLSD11008ADC-2Q-HV
Ambient Temp. -10~45 ℃, -40-65℃
Power Voltage: 110VAC (45-140V) or 155VDC (60-195V)
Peak Current: 4-8A
Continuous Current: 2-4A
PWM: 15KHz
Ramp Time: 0.2-2.2S
Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz
Alarm Output: OC
PG Output: 4 or 24 Pulse/r @8-Pole Motor
PI Close-Loop: Speed or Current.
SC Protection(A): 20
OT Protection: 65℃ or 85 ℃ at Case
Safe F/R: Smooth F/R Operation
Safe Start: Stop Until Speed is Zero at Starting
Model No. BLSD11016ADC-2Q-HV
Ambient Temp. -10~45 ℃, -40-65℃
Power Voltage: 110VAC (45-140V) or 155VDC (60-195V)
Peak Current: 8-16A
Continuous Current: 4-8A
PWM: 15KHz
Ramp Time: 0.2-2.2S
Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz
Alarm Output: OC
PG Output: 4 or 24 Pulse/r @8-Pole Motor
PI Close-Loop: Speed or Current.
SC Protection(A): 40
OT Protection: 65℃ or 85 ℃ at Case
Safe F/R: Smooth F/R Operation
Safe Start: Stop Until Speed is Zero at Starting
Model No. BLSD11024ADC-2Q-HV
Ambient Temp. -10~45 ℃, -40-65℃
Power Voltage: 110VAC (45-140V) or 155VDC (60-195V)
Peak Current: 12-24A
Continuous Current: 6-12A
PWM: 15KHz
Ramp Time: 0.2-2.2S
Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz
Alarm Output: OC
PG Output: 4 or 24 Pulse/r @8-Pole Motor
PI Close-Loop: Speed or Current.
SC Protection(A): 60
OT Protection: 65℃ or 85 ℃ at Case
Safe F/R: Smooth F/R Operation
Safe Start: Stop Until Speed is Zero at Starting
Model No. BLSD22008ADC-2Q-HV
Ambient Temp. -10~45 ℃, -40-65℃
Power Voltage: 220VAC (45-275V) or 310VDC (60-385V)
Peak Current: 4-8A
Continuous Current: 2-4A
PWM: 15KHz
Ramp Time: 0.2-2.2S
Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz
Alarm Output: OC
PG Output: 4 or 24 Pulse/r @8-Pole Motor
PI Close-Loop: Speed or Current.
SC Protection(A): 20
OT Protection: 65℃ or 85 ℃ at Case
Safe F/R: Smooth F/R Operation
Safe Start: Stop Until Speed is Zero at Starting
Model No. BLSD22016ADC-2Q-HV
Ambient Temp. -10~45 ℃, -40-65℃
Power Voltage: 220VAC (45-275V) or 310VDC (60-385V)
Peak Current: 8-16A
Continuous Current: 4-8A
PWM: 15KHz
Ramp Time: 0.2-2.2S
Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz
Alarm Output: OC
PG Output: 4 or 24 Pulse/r @8-Pole Motor
PI Close-Loop: Speed or Current.
SC Protection(A): 40
OT Protection: 65℃ or 85 ℃ at Case
Safe F/R: Smooth F/R Operation
Safe Start: Stop Until Speed is Zero at Starting
Model No. BLSD22024ADC-2Q-HV
Ambient Temp. -10~45 ℃, -40-65℃
Power Voltage: 220VAC (45-275V) or 310VDC (60-385V)
Peak Current: 12-24A
Continuous Current: 6-12A
PWM: 15KHz
Ramp Time: 0.2-2.2S
Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz
Alarm Output: OC
PG Output: 4 or 24 Pulse/r @8-Pole Motor
PI Close-Loop: Speed or Current.
SC Protection(A): 60
OT Protection: 65℃ or 85 ℃ at Case
Safe F/R: Smooth F/R Operation
Safe Start: Stop Until Speed is Zero at Starting
Selection Table
Notice
- Select peak current of driver: IP≥2*Irm or IP≥4*Pom/(1.414*Vp),
Irm=rated current of moto (A), Pom=Rated Output power of motor (W),
Vp=AC Supply voltage of driver (Vrms)
- Driving quadrant: The drivers are only used in I & III quadrant.
- Interference from leads: The Hall signals can be disturbed by
switched current in windings leads when length is more than 3m.
Don’t interwire them together. It is better to use shield leads
- Motor Insulation: Hall sensors to windings/Hall sensors to Motor
Case/Windings to Motor Case
Insulation Resistance＞100MOhm @ 1500VDC
Dielectric strength ＜1 mA@1200VAC/50-60Hz/1 minute
- Safety: The PE terminal labeled on the driver must be connected to
the protection earth point of the supply system.
