12V/24VDC input electronic water pump for Battery Management System
and intercooler of passenger vehicles.
Applications
Widely used in hybrid bus, hybrid passenger car, electric vehicles,
trains, and ships and heating management system of energy storage,
liquid cooled charging pile, immersed cooling circulation system of
data center and other heating and cooling circulation system.
Features
◆Centrifugal pump
◆Magnetic force transmission (shield pump structure)
◆High efficiency brushless DC motor, low power consumption, high
efficiency, long service life.
◆With wide range operating temperature
◆PWM signal speed controlling
◆With constant flow controlling
◆Reverse polarity protection
◆Dry running protection
◆Over Voltage, over current protection
◆Overload, over temperature protection
Technical description (related parts in contact with the liquid)
Pump head housing: PPS+GF
Impeller: PPS+GF
Shield cavity: PPS+GF
Shaft sleeve: Carbon resin composite materials
Shaft: stainless steel shaft
Magnet housing: nylon plastic capsulation
Seal ring: EPDM
Driving device (Including motor)
Driving electromagnet: nylon plastic capsulated magnet
Screws and nuts: SUS 304 stainless steel
Driving Motor : brushless motor
Motor wire frame :PPA GF
Pump housing: Die-casting aluminum case with sandblasting and
impregnation treatment
Bracket: Steel with powder coating
Bracket hoop: US 304 stainless steel+ Damping rubber ring
Waterproof based on IP68 rating (en60529)
Connector model: AMP282106-1(matched Plug AMP282088-1)
Nozzle diameter:22.4mm (inner diameter:16mm)
Model Specifications
OWP-BL93-300-(12VDC)
OWP-BL93-301-(24VDC)
Mounting instruction
OWP-BL93-300 series pumps are centrifugal pumps which require
pre-filled,
The pump installed in the lowest position of the system to ensure
that the impeller is always
immersed in the liquid, or pre-filled the pump before power on .
1: Pump should not be dry-running, even though it can dry-running
for 30 seconds (after 30
seconds dry-running, it will automatically stop), Dry running will
makes noise, also increasing
abrasion to the shaft and shaft sleeve.
2:Use the recommended diameter pipe connecting the pump inlet, if
you use a smaller diameter
hose pump inlet, Due to the negative pressure in the pump, the
outside air easier enter to the
pump through the pipeline, it will make the pump performance
degradation, and also the air
bubbles make damage to the pump.
3: As viewed from the pump inlet direction, the impeller rotates
clockwise (see the arrow on
the outlet port).
4: The pump can be installed vertically or horizontally mounted
(see figure 1 ) When installed
vertically, the outlet port should be upward .
5:In order to avoid the dry- running (air get stuck in
impeller),the water pump outlet port should
be vertical or in the upper of the impeller. (see figure 1 )
6: The connected pipe should be vertically mounted (or no elbow in
20cm )to make the air
discharged easily, the outlet pipe should not be used less than 90
degrees
Elbow (see figure 2).
7: Can't use the seawater or other heavy pollution with big grain
impurity liquid as the liquid
medium .
Figure 1 Figure 2
Temperature parameter
Medium liquid temperature: -40℃ to +85℃ (-40°F to + 185°F)
Working ambient temperature: -40℃ to +85℃ (-40°F to +185°F)
Humidity ≤90%
Storage temperature: -40℃ to +70℃ (-40°F to +158°F) (up to 100 ℃,
but it will shorten the
service life)
System pressure
-0.2 to 2.5 bar ( 100℃ (212°F).
The service life is more than 20,000 hours based on the rated
voltage and 36℃(86°F) ambient
temperature.
Voltage range
Rated 12V water pump, workable range 9V - 16V
Rated 24V water pump, workable range 18V - 30V
Although the motor can be used in a wide range of voltage and
temperature, but excessive or too
low voltage and temperature will affect the service life of the
motor, the pump can not be
exposed to thermal radiation ambient.
Medium liquid: pure water, liquid mixture (Water with below 60%
glycol)
Electrical parameter
PWM character
Attentions
1. Working ambient temperature:-40℃--85℃, should try to avoid close
to three-element
catalytic, gas discharge pipe system and engine during the
installation, ensure the working
environment temperature.
2.The installation position of the water pump should as much as
possible close to the low water
level , to extend the service life of the pump.
3. Please use the pump far from the dusty environment, the dust is
harmful to reduce the service
life
4. Pay attention to the purity of the water, avoid to jam and
impeller-blocked to reduce the
service life of pump
Performance parameter
External dimensions
