SC UPC Plastic Field Installable Connector 5G 4G Single Mode Multi
Mode
FTTH Drop Cable 2x3mm Optical Fiber SC UPC Field Assembly Fast
Termiantion Connector 5G 4G Single Mode
The SC/APC fast connector are factory pre-polished,
field-installable connectors that completely eliminate the need for
hand polishing in the field. Proven mechanical splice technology
ensuring precision fiber alignment, a factory pre-cleaved fiber
stub and a proprietary index-matching gel combine to offer an
immediate low loss termination to either single-mode or multi-mode
optical fibers.
Specification
| ITEM | Parameter |
| Insertion loss | ≤ 0.3dB (1310nm & 1550nm) |
| Return loss | ≤ -45dB |
| Bare fiber strength | >5N |
| Clad strength | >10N |
| tension | >50N |
| Mechanical durability | IL ≤ 0.2dB & RL ≤ 5dB |
| Operating Temperature | 5 ºC to +70 ºC |
| Repeat time | >50times |
| Length | 53mm |
| Comply standard | IEC61754-4 |
| Life span | 30years |
Pack Information:
1pc/plastic bag, 100pcs/inner box, 10pcs inner box/carton box
Product Details:
This fast connector use ceramic C-groove structure not plastic or
metal, Insertion loss: the average ≤0.2dB, MAX≤0.4dB, Return loss:
≥50dB.
No need epoxy or polished, field-installable, factory embedded
fiber
This connector is SC / UPC, cover type, total length 53mm, will
have english user manual along with the shipment.
Apply to 2mm* 3mm or 2.0*1.6mm flat drop cable, which have fix jig.
to hold the cable at the boot for both types of cable.
Boot is flip up and down type design, there is a black re-open tool
for multiply use.
It is good sealing performance, flame retardant, and high quality
plastic. All products with UPC flat ferrule, and with dust cap
before delivery, and each with individual package.
How to use the fast connectors?
Process the fiber
1. Insert the drop cable into the stripper till 50-60mm out, and
strip the cable strength layer
2. Press the stripped cable into the clamp, there are 4points to
lock the fiber
3. Strip the cable coating layer by the insert the longitudinal
fiber stripper to strip the coating of the fiber. Or use Miller
stripper align of the fiber clamp.
4. Check the fiber by bending about 60°into direction if ok
5. Clean the fiber with alcohol cloth by 0°wipe and 90°again
6. Put the clamp into the length fixer till arrow up, and press to
the end
7. Lay flat on the fiber cleaver slot, align to the end, and then
cut the fiber
8. Finally the fiber length will be :19.4mm and 29.4±0.1mm,see
picture
Assembly
Check the black locker
Insert the fiber along with the V entrance till fiber bend, but not
higher than 1mm than V entrance
Keep housing, coating, and jig on the same level, take off the
switch.
Dis-assembly
Assemble the auxiliary jig,fit on switch to the right end
Unlock the fiber
Use the exclusive convex to open the cover, unlock the shell
Raise 15°to pull out the fiber
Other Similar Types:
Application
- Premise environments
- Connections at the desk for LAN environments
- Patch panels
- Direct equipment termination
- Fiber to the Subscriber / Home (FTTH) applications
- Repair/replacement requirements
- Equipment test leads
2. Apply to 2mm* 3mm or 2.0*1.6mm flat drop cable
3. Ceramic C-groove structure not plastic or metal, good sealing
performance, flame retardant
4. Insertion loss: the average ≤0.2dB, MAX≤0.4dB
5. Return loss: ≥50dB
6. No need epoxy or polished, field-installable, factory embedded
fiber
