Non-contact Infrared Temperature Sensor
Operator’sGuide
ST03 non-contact infrared sensors measure temperature from 0°C to
1200°C and provide a linear 4 to 20mA output. This output signal is
compatible with almost any indicator, controller, recorder, data
logger ect., without the need for special interfacing or signal
conditioning. They are suitable for most materials such as food,
paper, textiles, plastics, leather, tobacco, pharmaceuticals,
chemicals, rubber, coal and asphalt; but mot materials with low
emissivity, for example polished metals. Two-wire
CS20L4sensorstransmit thetarget temperatureasa 4-20mA output and
offer a simple solution for most applications.
GENERAL SPECIFICATIONS
| Part number | ST03 |
| Measuring range | 0~100/200/250....../1200°C |
| D:S | 20:1 |
| Accuracy | ±1.5% or ±1.5°C(whichever is greater) |
| Emissivity | 0.95(fixed) |
| Response time | 240 ms (90% response) |
| Spectral response | 8 to 14µm |
| Output | 4~20 mA |
| Supply Voltage | 5~30V DC |
MECHANICAL SPECIFICATIONS
| Construction | Stainless Steel |
| Dimensions | 19mm diameter x 113mm length |
| Thread (sensing head) | M18x1 |
| Cable length | 1.5m as standard |
| Weight with 1.5m cable | 180g |
ENVIRONMENTAL SPECIFICATIONS
| Environmental Rating | IP65 |
| Ambient Temperature Range | 0°C to 60°C |
| Relative Humidity | 95% maximum non-condensing |
ACCESSORIES
A range of accessories to suit different applications and
industrial environments is available. These may be ordered at any
time. The accessories consist of the following parts. Fixed
mounting bracket Adjustable mounting bracket Air purge collar Laser
sighting tool
OPTICAL CHART
The optical chart below indicates the nominal target spot diameter
at any given distance from the sensing head and assumes 90% energy.
INSTALLATION
The installation process consists of the following stages:
Preparation Mechanical installation Electrical installation Please
read the following sections thoroughly before proceeding with the
installation.
PREPARATION
Ensure that the sensor is positioned so that it is focused on the
target only.
Distance and spot size
The size of the area (spot size) to be measured determines the
distance between the sensor and the target. The spot size must not
be larger than the target. The sensor should be mounted so that the
measured spot size is smaller than the target.
Ambient temperature
The sensor is designed to operate in ambient temperatures from 0°C
to 60°C. For ambient temperatures above 60°C, an air/water-cooled
housing will be required. Avoid thermal shock. Allow 20 minutes for
the unit to adjust to large changes in ambient temperature.
Atmospheric quality
Smoke,fumes or dust can contaminate the lens and cause errors in
temperature measurement. In these types of environment the air
purge collar should be used to help keep the lens clean.
Electrical interference
To minimize electromagnetic interference or ‘noise’, the sensor
should be mounted away from motors, generators and such like.
Wiring
Checking the distance between the sensor and the
indicating/controlling device. If necessary, the CS20L4 sensor can
be ordered with a longer cable attached.
Models with thermocouple output
When extending the cable, ensure thermocouple extension cable and
connectors are used.
Power supply
Be sure to use a 5~30V DC (>25mA) power supply.
MECHNICAL INTALLATION
All sensors come with a 1.5m cable and a mounting nut. The sensor
can be mounted on brackets or cut outs of your own design, or you
can use the fixed and adjustable mounting bracket accessories.
ELECTRICALINSTALLATION
OPERATING
Once the sensor is in position and the appropriate power, air,
water, and cable connections are secure, the system is ready for
continuous operation by completing the following simple steps:
1. Turn on the power supply
2. Turn on the meter, chart recorder or controller
3. Read/monitor the temperature.
