Product: Smart BMS with Bluetooth for 16S 48V LifePO4 Battery Pack With NTC
100A Discharge Current
Customer can adjust the paramter of overcharge or overdischarge by
the parameter sitting if customer need to.
Attention:
Customer need to identify the battery's series, then choose the
same series BMS. Such as your battery is 24S, you must choose 24S
BMS, can not choose 20 or other one. The number of series of BMS is
fixed ,not adjustable once the BMS is shipped out .
◆ Control instructions: remote control device monitoring.
◆ Vehicle icon: data transmission send command
◆ Statistical report: Collect the data information, the customer
can monitor the battery capacity & other alarm infomation.
◆ Electronic fence: fence setting limit range.
◆ Device information: device parameter information, etc.
The information on your battery can be checked on your host
computer, then you can monitor your battery status anytime. Which
is easly control your device. Smart BMS make our life to become
easy.
What advantage of the BMS?
1. Use top quality (A-level) protective integrated circuit IC, from
the solution of Seiko of Japan.
2. Strong load ability, use high voltage resistance, low inner
resistance power Mosfet. The heat sink will greatly help cooling.
3. IC itself has power balancing function. The circuit is simple
and reliable.
4. Typical voltage detection for each cell. So each battery will be
prevented over charged or over discharged. Over current and short
circuit protection function is very reliable.Long time short
circuit of the load won't affect the PCB and the
battery.Temperature protection can be added.
5. Extreme low power consumption. The consumption of the whole
device is less than 50uA.
6. PCB use high anti-corrosion, high water resistance, high
impedance ESD conformal Coating.
What do we supply with the bms?
| Bluetooth module | choose by customer |
| UART to USB cable | choose by customer |
| USB to USB cable | choose by customer |
| CAN to USB module | choose by customer |
| Power indicator | choose by customer |
| LCD touch screen | choose by customer |
What Applications for the BMS?
- Energy Storage
- Low speed CAR
- Tricycle
- Electric motorcycle
- Scooter
- Emergency UPS
- Solar street light
- RV&Home energy
- More application
Defaulted Specification
| Datasheet for 3.2V LifePO4 BMS( 80A-250A ) |
| Content | Spec | Unit | Remark |
| 80A | 100A | 120A | 150A | 200A | 250A | | |
| Discharge | constant discharge current | 80 | 100 | 120 | 150 | 200 | 250 | A | |
| Over-discharge current protection | 250±50 | 300±50 | 400±100 | 500±10 | 600±100 | 600±100 | A | |
| charge | charge voltage | Series No. * 3.65 | V | |
| charge current | 40 | 50 | 60 | 75 | 100 | 125 | A | Common port |
| charge current | 50A as default | A | Separate port |
| Over charge protection | over charge volt | 3.75±0.025 | V | |
| over charge volt protect delay | 1 | S | |
| Over charge volt release | 3.55±0.05 | V | |
| Power balancing | Power balance volt | 3.5 | V | |
| balance release volt | 3.5 | V | |
| balance current | 35±5 | mA | |
| Over discharge protection | Over discharge detect volt | 2.2±0.1 | V | |
| Over discharge detect delay | 1 | S | |
| Over discharge volt release | 2.7±0.05 | V | |
| Over current protection | Over current detect delay | 1 | MS | |
| Over current protect release | Off-load | | |
| Short circuit protection | Short circuit protection | External load short circuit | | |
| Short circuit detect delay | 250 | uS | |
| Short circuit detect release | Off-load | | |
| Temperature protection | Temp protection | charge＜0℃, discharge＞70℃ | ℃ | Can be customized |
| resistance | Main circuit resistor | ≤20 | mΩ | |
| Self-consumption | Working current | 100 | uA | |
| Sleepy current(when battery is over discharged ) | ≤20 | uA | |
| Working temp | temp range | -40~80 | ℃ | |
| Storage temp | Temp range | -40~80 | ℃ | |
Wire specification
| Current | Wire | Square |
| 10-15A | 16AWG | 1.3mm² |
| 20A | 14AWG | 2mm² |
| 30A | 12AWG | 3.4mm² |
| 40A-60A | 10AWG | 5.3mm² |
| 80A | 8AWG | 8.3mm² |
| 100A | 7AWG | 12mm² |
| 120A-150A | 6AWG | 16mm² |
| 200A-250A | 6AWG*2 | 16mm²*2 |
| 400A | 2AWG*2 | 35mm²*2 |
How to test if the bms is good or not?
1. Make sure to use the attached detective wires of our bms.
Ensure volt-detect red wires are connected correctly.
2. Connect the wire to the battery pack,measure the voltage through
the wire,it should be equal with the voltage of each cell.
If the votage is different,it means wrong wiring.
3. Make sure the voltage is same,plug the bms in.Make the
multimeter point to Ω, measure the resistance between P- and B-. If the resistance is 0, then the BMS is good.
BMS wiring directions
First, Preparation before installation.
Make sure the batteries are of good consistency.The volt difference
is no more than 0.05V,inner resistance is no more than 5mΩ,capacity
difference lower than 30mAh. Connect the batteries in parallel
first and then in series.the better performance of batteries
consistency is, the higher performance of the BMS.
Second, wiring instructions.
Attention: please use our wires for our BMS.Don’t use other
factories’ wires which can’t match with our BMS.
Step 1 B-(blue thick wire): Connect to battery pack total negative pole -
Step 2, Disconnect the wires for batteries from the BMS side.
Step 3,Connect the wires to batteries. Start from the thick black wire to total negative pole(B1-),then connect the 2nd red thin wire to the 1st battery positive pole(B1+)
B2+,B3+B4+......till the last red thick wire.
Step 4,Finishing all the wires to each batteries,don’t plug into
the BMS directly. We suggest you use multimeter measure the voltage
of two adjacent metal terminals(You can see the white connector
with silver metal pins on the BMS).if the voltage is
3.0~4.2V(LiNCM),2.0~3.6V(LiFepo4), 1.5~2.75V(LTO),which means the
wiring is correct.
Step 5,Ensure the wires are connected to batteries correctly, all
voltage is normal, you can plug the wires into the BMS.
Step 6 P-: Connect P-(black thick wire) to load - and charger -
(if you ordered “common port”)
Charger+ connect to C-(yellow wire) load+ connect to P-(Black thick wire)
(if you ordered “separate port”)
Step 7 charger+ and load+ connect to battery +,please use thick
wire
Third, Measure the total volt of the pack, and the output voltage
of the BMS.if the voltage is the same,it means the wiring is
correct.You can use the BMS now. Otherwise please check the wiring
again according to the tips above.
