1/4'' 8mm Push To Quick Connect Union Elbow Pneumatic Hose Fittings
Push-Fit fittings, also known as Push-to-Connect fittings are
east-to-install pneumatic accessories that work by pushing the
tubing in to engage it—it's like putting a cap lid on. Pneumatic
fittings are used for valves, control panels and a large variety of
other domestic and industrial applications.
Brando’s broad selection of pneumatic fittings provide connectivity
solutions for a whole range of pneumatic applications. We offer a
broad portfolio of products within our pneumatic fittings range and
have plenty of material options and device configurations to suit
the demands of your project which are easy to install. They also
have the capability to withstand a variety of industrial media. Our
pneumatic fittings are suitable for use in a wide variety of
applications serving across many of today's major industrial
markets.
Dimension & Order Code of Pneumatic Hose Fittings:
Union Straight Fitting:
| Picture | Dimension | Part No. | D | D1 | L |
 |  |
| PUC4 | 4 | 11 | 33 |
| PUC6 | 6 | 13 | 34 |
| PUC8 | 8 | 14 | 39 |
| PUC10 | 10 | 18 | 46 |
| PUC12 | 12 | 21 | 47 |
Union Elbow Fitting:
| Picture | Dimension | Part No. | D | D1 | L |
 |  |
| PUL4 | 4 | 11 | 19 |
| PUL6 | 6 | 13 | 20 |
| PUL8 | 8 | 14 | 23 |
| PUL10 | 10 | 18 | 27 |
| PUL12 | 12 | 21 | 30 |
Union Tee Fitting:
| Picture | Dimension | Part No. | D | D1 | L |
 |  |
| PUT4 | 4 | 11 | 19 |
| PUT6 | 6 | 13 | 20 |
| PUT8 | 8 | 14 | 23 |
| PUT10 | 10 | 18 | 27 |
| PUT12 | 12 | 21 | 30 |
| Picture | Dimension | Part No. | D | D1 | L |
 |  |
| PY4 | 4 | 11 | 37 |
| PY6 | 6 | 13 | 40 |
| PY8 | 8 | 14 | 41 |
| PY10 | 10 | 18 | 49 |
| PY12 | 12 | 21 | 53 |
List of All Plastic Pneumatic Hose Fittings:
Directions for use!
1. The Tube Fitting is Prohibited Where Spark and Fire Might Be
Occurred.
2. Do Not Exceed 145Psi Pressure.
3. Working Temperature: 0-60°c,do Not Use Outside the Service 4.
Temperature Range to Prevent Deformation of the Sealing Material
and Easy Leakage.
5. Do Not Use in Places with Too Much Dust or Particles
6. Do Not Use Any Medium Other Than Air. the Product is Limited to
Air or Vacuum Environment.
7. After Completing the Connection, Please Gently Pull the Tube
with Your Hand to Make Sure That It is Completely Connected Without
Falling Off.
8. Make Sure That the Cutting Surface of the Pipe is Vertical,
There is No Scar on the Outer Circumference of the Pipe and the
Pipe is Not Oval.
9. Never Apply Tube Joint with Additional External
Load(bending,twist or Pulling),otherwise Damage or Leakage Will Be
Occurred.
10.When Inserting the Pipe, It Must Be Inserted into the Bottom of
the Joint. Failure to Insert the Pipe into the Bottom May Lead to
Air Leakage.
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
