Telescoping Mobile Surveillance 18M Endzone Camera System
product introduction:
Surveillance mast is designed for communications, reconnaissance,
and surveillance applications.
This mast is lightweight and mobile, allows internal or external
mountings for MRAP or shelter installations.
The masts are made up of multiple segments, each of which is
spinning.
Attaching a few cables to the top of a tower and the other end to
the ground, the mast can easily be pulled down.
specification:
hand winch up
| extended height (m) | No. Of section | Retracted height(m) | Outer tube range(mm) | Self weight (kg) | Max.payload (kg) |
| 3 | 2 | 1.6 | T50-T60 square | 3 | 50 |
| 4 | 3 | 1.4 | 50-60 -T70 | 4 | 40 |
| 5 | 3 | 1.77 | 50-60- T70 | 5 | 40 |
| 6 | 4 | 1.6 | 50-70 -T80 | 6.5 | 30 |
| 7 | 4 | 1.85 | 50-70- T80 | 7 | 30 |
| 8 | 5 | 1.7 | 40-70-T80 | 9 | 20 |
| 9 | 5 | 1.9 | 40-70- T80 | 10 | 20 |
| 10 | 6 | 1.75 | 40-80-T100 | 12 | 15 |
| 12 | 7 | 1.8 | 40-90-T100 | 28 | 10 |
| 15 | 8 | 1.95 | 40-100-T120 | | 10 |
Note: bottom square tube show as T-70, means: 70*70mm square tube
product photo:
features:
- 3 to 15m full extended models
- Car suitable transport length
- Hand push up
- Max 80mm Diameter Bottom Section -
- 25mm Diameter Top Section
- Aluminum 6063 tube 2mm thickness
- Stainless steel clamp fast fasten, without tool
- COMMERCIAL QUALITY
|
Application areas:
For WiFi, Portable Antennas, Elevated Photos
Ideal for:Emergency Response Antenna Systems, Restricted Space
Antennas - Prepping Systems
Elevated Photography - Weather Instruments - WiFi Site Surveying -
End Zone Cameras
Accessories:
Usually these masts require a flat or socket wrench, with the quick
release clamps you can raise and lower the masts without any tools.
Even with limited space these quick clamps can be easily used,
because the lever can be adjusted at any position. Just pull out
and release the lever, the strong spring latches the lever at the
desired position.
Attentions:
The mast can be extended to any length and securely locks into
place by means of a massive clamp. The maximum allowed extended
length is marked by a color ring approx. 20cm before the end of
each tube. There is no fixed stop which makes it advisable to
approach the marking slowly when extending the telescopes.
These masts are ideally suited for portable applications due to the
low weight and the telescopic mechanism. When setting up the mast
please pay special attention to the clamping length; the clamping
length of the mast must be at least 1/6th of the extended length,
or at least 1 meter at the minimum. When extending the mast more
than 6 meters measured from the uppermost clamping point additional
guys are mandatory.
The tubes are made of weather-proof aluminum alloy. The tubes are
tapered by 5 mm and the tube thickness is 2mm. Please refer to the
following table for weight and dimensions. The stated additional
forces refer to a horizontally applied force at the tip of the
extended mast - without guys and a mast clamping length of 1/6th.
The calculation includes the inherent load at a wind speed of
50km/h (which is equivalent to a wind force of 7).
also we can produce according to clients special requests, and can
give proposals.
Packing, delivery tiem, and shipping:
We will close then pack the goods safely in solid wooden box.
Prodcution lead time for sample: 2 weeks; 4 weeks for bulk order
Ship by sea, air, or express according to your request.
