Product Name
Medical Blood Oxygen Saturation Pulse Monitoring Home Heartbeat
Heart
Rate Detector Oximeter Finger Clip
Function Specification
| Display Information | Display Mode |
| The Pulse Oxygen Saturation(SpO2) | LED |
| Pulse Rate(PR) | LED |
| Pulse Intensity (bar -graph) | LED |
| Pulse wave | LED |
| SpO2 Parameter Specification |
| Measuring range | 0%~-100%, (the resolution is 1%). |
| Accuracy | 70%~100%±2%, Below 70% unspecified. |
| Optical Sensor | Red light (wavelength is 660nm) Infrared (wavelength is 880nm) |
| Pulse Parameter Specification |
| Measuring range | 30bpm~250bpm (the resolution is 1 bpm) |
| Accuracy | ±2bpm or±2% select larger |
| Pulse Intensity |
| Range | Continuous bar-graph display, the higher display indicate the
strong pulse |
| Battery Requirement |
| 1.5V (AAA size) alkaline batteries x 2 or rechargeable battery |
| Battery Useful Life |
| Two batteries can work continally for 20 hours |
| Dimensions and Weight | |
| Dimensions | 57(L) x 31(W) x 32(H) mm . |
| Weight | About 50g (with the batteries) |
Troubleshooting
| Trouble | Possible Reason | Solution |
The SpO2 and Pulse Rate can not be displayed normally
| 1. The finger is not properly positioned. 2. The patient's SpO2 is too low to be detected.
| 1. Place the finger properly and try again. 2. Try again; Go to a hospital for a diagnosis if you are sure the
device works all right. |
The SpO2 and Pulse Rate are not displayed stably
| 1. The finger is not placed inside deep enough. 2. The finger is shaking or the patient is moving. | 1. Place the finger properly and try again. 2. Let the patient keep calm
|
The device can not be turned on
| 1. The batteries are drained or almost drained. 2. The batteries are not inserted properly. 3. The malfunction of the device. | 1. Change batteries. 2. Reinstall batteries. 3. Please contact the local service center.
|
The display is off suddenly
| 1. The device will power off automatically when it gets no signal within 5 seconds. 2. The batteries are almost drained. | 1. Normal. 2. Change batteries.
|
Warning
1,The uncomfortable or painful feeling may appear if using the
device ceaselessly, especially for the microcirculation barrier
patients. It is recommended that the sensor should not be applied
to the same finger for over 2 hours.
2,For the individual patients, there should be a more prudent
inspecting in the placing process. The device can not be clipped on
the edema and tender tissue.
3,The light (the infrared is invisible) emitted from the device is
harmful to the eyes, so the user and the maintenance man, can not
stare at the light.
4,Testee can not use enamel or other makeup.
5,Testee's fingernail can not be too long.
6,Please peruse the relative content about the clinical
restrictions and caution.
7,This device is not intended for treatment.
Operating Guide
1) Insert the two batteries properly to the direction, and then
replace the cover.
2) Open the clip as shown in Figure 5.
3) Let the patient's finger put into the rubber cushions of the
clip (make sure the finger is in the right position), and then clip
the finger.
4) Press the switch button once on front panel.
5) Do not shake the finger and keep t he patient at ease during the
process. Meanwhile, human body is not recommended in movement
status.
6) Get the infonnation directly from screen display.
7) The button has three functions. When the device is power off,
pressing the button can open it; When the device is power on,
pressing the button shortly can change direction of the screen;
When the device is power on, pressing the button long can change
brightness of the screen
► Fingern ails and the luminescent tube should be on the same side
