48 PoE+ 1440W Cisco Network Switch S5730S-68C-PWR-EI

Four 10GE SFP+ ports

Applicable modules and cables:

· GE optical module

· GE-CWDM optical module

· GE-DWDM optical module

· GE copper module (100M/1000M auto-sensing)

· 10GE SFP+ optical module (OSXD22N00 not supported)

· 10GE-CWDM optical module

· 10GE-DWDM optical module

· 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables

· 3 m and 10 m AOC cables

· 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking)

One PNP button

NOTICE:

Applicable in V200R012C00 and later versions:

To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.

To reset the switch, press the button.

Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.

One console port

NOTE:

It is used with a console cable. The console cable is not delivered with the switch and needs to be separately purchased if needed.

Ground screw

NOTE:

It is used with a ground cable.

ESN label

NOTE:

You can draw it out to view the ESN and MAC address of the switch.

Rear card slot

NOTE:

Card supported:

· ES5D21Q04Q01

· ES5D21VST000 (applicable in V200R012C00 and later versions)

Fan slot

NOTE:

Applicable fan module: FAN-028A-B

Power module slot 2

NOTE:

Applicable power modules:

· 500 W AC PoE power module

· 650 W DC PoE power module

· 1150 W AC PoE power module

· 1000 W AC PoE power module (applicable in V200R013C00 and later versions)

Power module slot 1

NOTE:

Applicable power modules:

· 500 W AC PoE power module

· 650 W DC PoE power module

· 1150 W AC PoE power module

· 1000 W AC PoE power module (applicable in V200R013C00 and later versions)

• Using 500 W AC or 1000 W AC power modules: ±6 kV in differential mode, ±6 kV in common mode
• Using 650 W DC or 1150 W AC power modules: ±2 kV in differential mode, ±4 kV in common mode

44.4 mm x 442.0 mm x 420.0 mm (1.75 in. x 17.4 in. x 16.5 in.)

When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 507.3 mm (19.97 in.).

Any 10GE SFP+ or 40GE QSFP+ ports

Ports on the 2-port QSFP+ rear stack card

100 V AC to 240 V AC, 50/60 Hz

-48 V DC to -60 V DC

90 V AC to 264 V AC, 47 Hz to 63 Hz

-38.4 V DC to -72 V DC

• Using 650 W DC or 500 W AC power modules
  • Not providing the PoE function: 68.3 W (without card)
  • 100% PoE loads: 925 W (system power consumption: 185.8 W, PoE: 739.2 W, without card)
• Using 1150 W AC or 1000 W AC power modules
  • Not providing the PoE function: 68.3 W (without card)
  • 100% PoE loads: 1733 W (system power consumption: 293 W, PoE: 1440 W, without card)