Product Description
Tank mounted with dryer and filter 16bar for laser cutting machine
use
Screw air compressor--parameters:
Model
specification | RMY-10AG | RMY-15AG | RMY-20AG | RMY-25AG | RMY-30AG | RMY-40AG |
Exhaust volume
Exhaust pressure
M³/Min Mpa | 0.7/1.3 | 1.2/1.3 | 1.0/0.8 | 2.2/1.3 | 2.6/1.3 | 2.3/0.8 |
| 0.5/1.6 | 1.0/1.6 | 0.9/1.0 | 1.8/1.6 | 2.2/1.6 | 2.0/1.0 |
Power/
Horse power | 7.5/10 | 11/15 | 15/20 | 18.5/25 | 22/30 | 30/40 |
| Exhaust temperature | ≤ Ambient temperature +8℃ |
| Intake temperature | ≤ 45℃ |
| Noise dB(A) | ≤ 68±2 | ≤ 70±2 |
| Oil Content(ppm) | ≈2 | | | | | |
| L(mm) | 1670 | 1670 | 1670 | 2280 | 2280 | 2280 |
| W(mm) | 850 | 850 | 850 | 930 | 930 | 930 |
| H(mm) | 1570 | 1570 | 1570 | 1920 | 1920 | 1920 |
| Weight(KG) | 516 | 556 | 596 | 756 | 806 | 856 |
| Diameter of outlet | 3/4" | 3/4" | 3/4" | 1" | 1" | 1" |
- Compressor Model: RMY-20A/16
- Power: 15kw/20hp IP55/F
- Belt driven/ Air cooling
- Voltage: 220v/380v
- Frequency:50Hz/60Hz
- Work compressor:16bar
- Air capaicty: 1.74m3/min
- Tank: 300liters
- Air dryer: R134
- Line filter: 4 grade
- Timer drainer 5pcs
Compressed air as auxiliary gas:
- For carbon steel plates, when compressed air is used as the
auxiliary gas for cutting, the section of the part will generate
relatively small burrs. The burrs are not sharp, and can be applied
to parts that do not require high cutting surface.
- Stainless steel plate, compressed air is used as auxiliary gas.
After the material is processed, the cutting surface will be
oxidized. When the cutting section is welded, the oxide will
produce slag and pores in the weld bead, which will affect the
quality of the weld and cause the strength of the welded part to
decrease. Therefore, if the compressed air is used as an auxiliary
gas for cutting, and the parts need to be welded after cutting, the
oxide layer of the welded part needs to be polished to improve the
welding quality; in addition, the oxidation of the cutting surface
will become a yellow oxide layer, When re-welding, the oxide layer
needs to be polished.
- Aluminum plate and aluminum alloy plate, which uses compressed air
as auxiliary gas, will reduce the cutting burr; if using nitrogen,
the cutting burr will increase.
Laser cutting three auxiliary gases:
- Laser cutting machine uses different auxiliary gas to cut different
materials. The thickness of the cutting material is not used, the
pressure of the auxiliary gas and the required flow rate are
different.
- There are three kinds of auxiliary gas for laser cutting machine,
laser gas, compressed air, auxiliary gas
Laser gas: the gas used to generate laser in the laser generator
Compressed air: generally used to protect the optical path, can
also be used as auxiliary gas
Auxiliary gas: gas ejected from the cutting nozzle of the cutting
machine
- Oxygen for carbon steel cutting is generally required to have a
purity of 99.5% or higher. The main function is to support
combustion and blow off the cut melt. The pressure and flow rate
vary according to the requirements of the cutting machine
manufacturer. It is related to the size of the cutting nozzle model
and the thickness density of the material. The general pressure
requirement is 0.3Mpa-0.8Mpa, the flow rate is not fixed, such as
cutting 22mm carbon steel, and some manufacturers require 10m3/h
(including the use of oxygen (Protect double-sided cutting nozzle).
- Nitrogen is used for cutting stainless steel to prevent oxidation
reaction and blow off the melt. The purity of nitrogen is
particularly high (stainless steel with a thickness of more than
8mm, the purity must reach 99.999%), and the pressure is generally
above 1.0Mpa. If you want to cut For stainless steel above 12mm or
25mm thickness, the pressure requirement will be 20Mpa or higher.
The flow rate is determined according to the type of cutting
nozzle. Generally 12mm thick stainless steel, the flow rate needs
150m3/h, and the thickness is 3mm stainless steel plate, the flow
rate is 50m3/ h.
PLC controller functions of our screw air compresosr:
1. Touch screen display shown
- loading and unloading status
- working hours
- current pressure, temperature
- full-load operation hours
- filters and oil replacement time
- running status
- motor running status
- main motor currency
- electric current
- cooling fan current
- cooling fan operation status
2. Automatically alarm functions:
- high temperature alarm
- oil change-over time arrive alarm
- air filter change-over time arrive alarm
- pressure, temperature sensor fault alarm
- oil filter change-over time arrive alarm
- oil separator change-over time arrive alarm
- communication fault alarm
- belt extended use alarm(belt driven compressor)
Fixed Speed Belt driven screw air compressor for laser cutting
machine--parameters:
| Model No. | RM-10AG | RM-15AG | RM-20AG | RM-25AG | RM-30AG | RM-40AG |
| Air capacity (m3/min/Mpa) | 0.7/1.3 | 1.2/1.3 | 1.7/1.3 | 2.2/1.3 | 2.6/1.3 | 3.6/1.3 |
| 0.5/1.6 | 1.0/1.6 | 1.5/1.6 | 1.8/1.6 | 2.2/1.6 | 3.2/1.6 |
| Power(KW/HP) | 7.5/10 | 11/15 | 15/20 | 18.5/25 | 22/30 | 30/40 |
| Noise dB(A) | 68±2 | 70±2 |
| Length (mm) | 900 | 900 | 900 | 1290 | 1290 | 1290 |
| Width (mm) | 850 | 850 | 850 | 900 | 900 | 900 |
| Height(mm) | 940 | 940 | 940 | 1190 | 1190 | 1190 |
| Weight(Kg) | 230 | 262 | 292 | 450 | 500 | 600 |
| Outlet size | 3/4" | 3/4" | 3/4" | 1" | 1" | 1" |
Permanent magnet Screw Air Compressors--16bar for laser cutting
machine use
Stationary type--parameters
| Model No. | RM-10AM | RM-15AM | RM-20AM | RM-25AM | RM-30AM | RM-40AM |
| Air capacity (m3/min/Mpa) | 0.7/1.3 | 1.2/1.3 | 1.7/1.3 | 2.2/1.3 | 2.6/1.3 | 3.6/1.3 |
| 0.5/1.6 | 1.0/1.6 | 1.5/1.6 | 1.8/1.6 | 2.2/1.6 | 3.2/1.6 |
| Power(KW/HP) | 7.5/10 | 11/15 | 15/20 | 18.5/25 | 22/30 | 30/40 |
| Noise dB(A) | 68±2 | 70±2 |
| Length (mm) | 900 | 900 | 900 | 1290 | 1290 | 1290 |
| Width (mm) | 850 | 850 | 850 | 900 | 900 | 900 |
| Height (mm) | 940 | 940 | 940 | 1190 | 1190 | 1190 |
| Weight (Kg) | 245 | 280 | 312 | 480 | 530 | 630 |
| Outlet size | 3/4" | 3/4" | 3/4" | 1" | 1" | 1" |
Our Services
Long interval maintenance periods:
Nearly ideal isothermal compression, direct driven method, smart
configuration and precision component design and machining, long
bearing service life, all of the above essentially extends interval
between regular periodical maintenance.
Company Information
Shanghai Royal Machinery Co.,Ltd is a high-tech enterprise which
specialized in sales and service of compressed air system
equipment, and after-treatment equipment, booster compressor,
diesel generator and drying equipment, etc.
We have an experienced team. It not only provide high-quality and
high-efficiency compressors for users but also provide the best
solution for air system equipment during before-sale, selling and
after-sale.
Welcome to contact us for inquires and quotation.
Packaging & Shipping
All of our screw air compressors are packed by export standard
plywood case:
Because of screw air compressor package volume and weight, most of
our screw air compressors are shipped by sea.
Wecome to contact us for more details, we will offer compressor
details, oil free screw air compressor use manual, oil free screw
air compressor configuration list, oil free screw air compressor
instruction drawings, spare parts list, installation drawings,
technical support and maintenance training.
Our CE certificate:
Air compressors can be grouped into three classifications: consumer
grade, professional grade and industrial grade.
- Consumer grade air compressors can be described as a pancake or
single-stage model. They’re used for household tasks like inflating
tires and inflatable products and possibly some low-load air tools
like staplers and brad guns.
- Professional grade air compressors provide more power and higher
pressurized air. They could be two-stage reciprocating models or
rotary screw models and can provide more power to run several air
tools at once with intermittent use.
- Industrial grade air compressors will be the workhorse of a
manufacturing plant or the reliable power source on an oil rig.
They are designed to provide a steady flow of compressed air for
long periods of time and can take fluctuating surges in use typical
in major manufacturing plants. These compressors are built with
high-quality components that allow for customization to the
specific environment to improve performance, energy efficiency and
reliability.
Here we offer i screw air compressors:
Power range: 5kw-400kw
Air flow: 1m3/min-75m3/min
#screwaircompressor
#scrollaircompressor
#pistonaircompressor
#oilfreeaircompressor
#oilinjectonaircompressor
#permanentmagnetvsdscrewaircompressor
#fixedspeedscrewaircompressor
#differentapplicationindustrialscrewaircompressors
#lasercuttingaircompressor
#allinoneaircompressor
#compactaircompressor
Welcome to container with us for more details
