explosion proof double cones rotary vacuum dryer with vacuum pump
Enamel or titanium tank for special matrial can be choosed.
Principle of Working
explosion proof double cones rotary vacuum dryer with vacuum pump
has double cone rotating tank. Under the state of vacuum inside the
tank, pass steam or hot water into its jacket for heating. The hot
amount can contact with the damp raw material through its inner
wall. The vaporized steam when the damp raw material absorbed heat
can be pumped out through vacuum exhaust pipe. Because its inner of
tank is in the state of vacuum and the raw material is turned over
all the time caused by the rotating of tank, the dry speed of raw
material is quickened and dry efficiency is raised too and the
purpose of uniform dry can be raised.
Features
1. Mixing and drying at the same time. Compensator equipped for
optional is used for solvent recover.
2. Advanced in design, simple in inner structure, easy for clean,
able to discharge all raw material, convenient in operation, lowing
labor intensity and improving work environment.
3. Meanwhile raw material is rotating accompanying with the
rotating of container, the wall of container cannot accumulate raw
material. Therefore, its coefficient of thermal transmission is
high and quick drying speed.
Application
explosion proof double cones rotary vacuum dryer with vacuum pump
is mainly used for drying following matters in medicine, chemical
and food industries:
1. Matters which cannot resist high temperature.
2. Matters which are easily oxidized.
3. Matters with crystals which should not be retrieved.
Technical Parameters
| Model | SZG100 | SZG350 | SZG500 | SZG-7500 | SZG1000 | SZG1500 | SZG2000 | SZG3500 | SZG5000 |
| Volume (litre) | 100L | 350L | 500L | 750 | 1000L | 1500L | 2000L | 3500 | 5000 |
| Charging volume (L) | 50 | 175 | 250 | 375 | 500 | 750 | 1000 | 1750 | 2500 |
| Loading weight(kg) | 40 | 120 | 200 | 300 | 400 | 600 | 800 | 1000 | 1800 |
| Heating area(m2) | 1.16 | 1.5 | 2 | 2.63 | 3.5 | 4.61 | 5.58 | 7.5 | 13.8 |
| Rotating speed(rpm) | 3~13 |
| Motor power | 0.75 | 1.1 | 1.5 | 2.2 | 3 | 4 | 5.5 | 7.5 | 15 |
| Rotating height | 1750 | 2100 | 2250 | 2490 | 2800 | 2940 | 2990 | 3490 | 4200 |
| Desigh pressure insider the tank: ---0.1~0.15Mpa |
| Desigh pressure inside the jacket: ≤0.3Mpr |
| Total weight (Kg) | 650 | 900 | 1200 | 1450 | 1970 | 2280 | 2500 | 2700 | 2900 |
Notes : 1. The above-mentioned parameters are calculated based on
material density 0.6g./cm3.if for reference only.
2. For raw material, if its volume has great change before and
after dry, then its filling coefficient may be increased or
decreased suitably.
3. Speed adjusting motor of 0~6rpm for optional according to user’s
requirement.
The following aspects should be point when order
If certificate for pressure vessel is requirement, please point
out.
if glass lining for interior surface is requirement, please point
out.
If the material is explosive, or flammable, the calculation should
be made according to trial result.1. If material has larger
specific weight, it shall be noted upon placing the order.
