Horizontal Washing And Drying Machine Easy Opration Glass Cleaning
Use
LIJIANG GLASS --SERVICE FOR WORLD GLASS MANUFACTURES
Horizontal Glass Washing And Drying Machine LJWBQJ2500
Glass Washing Machine LJWBQJ2500
LJWBQJ2500 used for cleaning and drying the upper and lower
surfaces of ordinary plate glass and high quality low-e glass,it is
composed of incoming segment, cleaning air-drying segment and
outgoing segment.
►►►►►
1.Aluminum alloy assembled structure, no scrap concept, permanent
use,high efficiency, energy saving 70% efficiency；
2. The rest of the sheet metal parts are sprayed with advanced
mechanical paint or powder；
3. The shaft of rubber roller is made of stainless steel ；
4. The washing part in contact with water is made of stainless
steel；
5. Cleaning department, wind staff overall lift, the maximum lift:
350mm,easy to clean and maintain；
6. Three pairs of brush(Ø150mm)Stainless steel shaft configuration
(low-e glass, ordinary coated glass and sunshine coated glass can
be washed without damaging the coated surface)；
7. Two pairs of special stainless steel aluminum alloy air knife
configuration, strong wind, good air drying effect, with heating
system(with temperature control device, optional opening and
closing)；
8. The fan is equipped with air filter in the air inlet chamber,
with large air volume and good air drying effect,The whole fan box
is installed in the upper part of glass washing machine, with the
air filter screen on the side for easy inspection and cleaning；
9. Main drive for gear transmission, frequency control, digital
display , the rotation of the brush roller in the washing section
is driven by independent belts of the upper and lower motors
respectively, the frequency conversion adjustment speed is stable,
the service life is long, realizes the cleaning high request
special glass；
10. Mechanical button control, cleaning machine digital display,
easy to operate, easy to operate, easy to maintain；
11. Washing machine water tank outside, convenient water tank
cleaning, water change, check, so that the washing machine cleaning
effect is cleaner.
12. Optional with PLC control, touch screen display.It is
convenient for workers to operate and maintain, and can be
connected to all manufacturers of edge grinding machines without
gap.(purchase separately if necessary)
►►►►►
►►►►►Stainless steel warter tank
►►►►►Adopt Profile design
►►►►►Fan Blower with low noise
Technical parameters
| Maximum glass width | 2500mm (effective maximum: 2650mm) |
| Minimum glass specification | 400mm×400mm (limited to single row on left and right sides) |
| Glass thickness | 3mm-25mm (digital display) |
| Speed range | glass thickness within 3-25mm Vmax=1-12m/min |
| Main drive, brush speed regulation method | frequency control |
| Table height | 900±25mm |
| Total power | 42KW(water-bearing wind heating: 15KW) |
| Water source | self-circulation, tap water (according to civil water standards)
and deionized water water supplement (deionized water equipment
shall be provided by the buyer) |
| Power source | 380V 50Hz |
| Weight | 3940kg |
LJWT02 Water treatment system
Description►►►
1. The quartz sand filter
Accumulative work is up to 8 ~ 20 hours, back flush for 20 minutes.
Accumulative work is up to 1.5 -2 hours, replace the quartz sand
filter material.
2. The activated carbon adsorption filter:
When exports residual chlorine content > 0.1 mg/L, should
replace the activated carbon filter material, normally when the
cumulative work is up to 1 year, replace the activated carbon
filter material.
3. The water softener:
Replace the softening resin for 1 year work
4. The security filter
Generally, cumulative work for three months ,a fine filter should
be replaced. When the fine filter pressure is less than 0.04 Mpa
and water shortage indicator light is on,a fine filter should be
replaced,too.
5. Inverse osmosis filter
After 6 months of work, application drug RO membrane should be
clean.
After 1-1.5 years accumulated work,we should replace the RO
membrane.
