220V 50Hz Handheld Laser Cleaning Machine Laser Rust Polishing
EquipmentFeatures
1. The fast speed at low cost.
2. It can protect the surface of the cleaning object, and make sure
that it is intact. For different dirt on different substrate
surfaces, the fiber laser cleaning machine can selectively clean
the dirt without damaging the substrate by setting laser parameters
such as spot size, single pulse energy, pulse width, repetition
rate, etc.
3. It can clean the surface of the fragile material. Since laser
cleaning is non-contact between the machine and the object, it is
convenient to carry out the cleaning operation. And very easy to
clean up the area in which other conventional cleaning methods
cannot be reached.
4. It’s environmentally friendly and green cleaning.
Technical Advantages:
Clean or remove the surface paint layer with high efficiency.
Accurate cleaning and rust removal effects;
No damage to the substrate;
Low cost, low consumption;
Fast investment recovery;
No need to sand grit or chemical;
Easy operation
Product parameters
| Items | Parameters |
| Cleaning Power | 50W |
| Current Consumption | Pout = Ponm / 5A |
| Max. Power | 400W |
| Power Voltage | AC 110/220V |
| Cooling Method | Air Cooling |
| Laser Class | Level 4 |
| Pulse Energy | 1.5mJ |
| Fiber Optical Cable | 5m(Customizable) |
| Laser Wavelength | 1064nm |
| Scan Width | 1-120mm |
| Preheat Time | 10-30s |
| Working Condition | A flat place without vibration and impact |
| Working Temperature | 0-60 ℃ |
| Storage Temperature | -10~+60℃ |
| Machine size | L462 x W 260 x H562 (855mm with pull rod) |
| Net Weight | 32Kgs |
Cleaning system setting page
● Field lens selection
Focusing mirror parameter selection, optional display 160mm focal
length, 254mm focal length, 330mm focal length
● Galvanometer speed
The mirror swing speed is adjustable. The X mirror is 50HZ at the
fastest and 50/30 per gear. The Y mirror is 200HZ at the fastest
and 200/30 per gear.
● Laser frequency
Laser pulse frequency, 1K-200K optional.
● Laser power
Laser output power can be adjusted from 1 to 100.
● Laser pulse width
Use it while using an adjustable pulse width laser machine
● Graphic length (laser pattern is square)
The length of the laser beam. The maximum length is 120MM, and the
length can be adjusted freely within the 0-120mm range.
● Graphic width (laser pattern is square)
The width is up to 4MM, and the width can be adjusted freely within
the 0-40mm range.
● Filling pitch
The distance between lasers while cleaning with a circular laser.
● Opening delay and closing delay
When the laser galvanometer speed is too fast and the graphic
length is too long, the ideal effect can be achieved by setting the
switching light delay.
● Outer circle radius (laser pattern is a ring)
The max. outer radius of the graphic outer circle is 40 mm, and the
radius can be adjusted during the circular size. When the graph is
circular, the inner circle radius is set to 0.
● Inner circle radius (laser pattern is a ring)
The figure is a ring, and the radius of the inner circle can be set
up to 40MM (but not larger than the radius of the outer circle). In
this range, the radius can be adjusted to change the ring size.
● Application
While parameters were set in the interface. If you enable this set
of parameters, click Application.
● Save
After setting the parameters in the interface, remember to click
“Save” to save the parameters for the next direct use.
● Red light
When the button is pressed, the red button turns red and the red
light comes out. Press again and the red button will return to gray
and turn off the red light.
● Laser
Laser light button, press the button, the laser light comes out. If
the red light is emitted at this time, the laser will be forced
out. Press the laser button again to turn off the laser light and
the button will return to gray.
● Group
Mode selection, you can save nine sets of data. Click on the number
on the left side of the mode, you can select the set mode
parameters freely, click on the application. Remember to save the
data after the parameter wat set in each interface.
