100w Laser Rust Removal System Portable Rust Descaling Machine 110V
/ 220VProduct description
(1) The laser cleaning machine is the latest high-tech product.
Easy to install, operate, easy to achieving automation. Plug-in
power, turn on and start cleaning - without chemicals, media, dust,
water.
(2) Cleaning with no detergent, no media, no dust, no water.
Autofocus, can clean curved surface, gentle cleaning surface.
Cleaning resin, oil stain, rust, coating materials, paints on the
workpiece surface.
Intelligent Automatic Laser Cleaning Equipment
The non-contact laser cleaning machine R&D by Super Fast is the
new high-tech product. It does not hurt the base material, no
consumables, energy-saving, and environmental protection. The
resin, oil, stains, dirt, rust, coating, plating, paint on the
workpiece surface can be removed with high efficiency. This meets
the requirements of complex modeling and precision production
cleaning in the industrial processing field, achieves a higher
level cleaning effect and lower production cost.
The machine mainly used for the automotive industry, machining,
electronic processing, cultural relics, mold industry,
shipbuilding, food processing, petrochemical, and other industries.
| Item | L/N | Characteristics | Test Conditions | Min. | Typical | Max. | Unit |
| Electrical Characteristics | 1 | Power Voltage | 220 | 210 | 220 | 230 | AC |
| 2 | Maximum current loss | Pout=Pnom | 4 | 5 | 6 | A |
| 3 | Total Power | 600 | 590 | 600 | 610 | W |
| 4 | Fiber Cable | 5 | 5 | 5 | 10 | M |
| General Characteristics | 1 | Working temperature range | 0 | / | 60 | ℃ |
| 2 | Storage temperature | -10 | / | 60 | ℃ |
| 3 | Laser power | 100 | W |
| 4 | Peak power | >10KW | KW |
| 5 | Cooling method | Air Cooling | |
| 6 | Laser level | 4 Class | |
| 7 | Pulse energy | 1.5mJ | mJ |
| 8 | Laser wavelength | 1064 | nm |
| 9 | Preheat time | Reach to start operation | 0 | s |
| Achieve complete stability | 10 |
| 10 | Humidity | 10 | / | 95 | % |
| 11 | Laser machine size | L647*W440*H859 | mm |
| 12 | Weight | 70 | kg |
Cleaning system setting page
● Field lens selection
Focusing mirror parameter selection, optional display 160mm focal
length, 254mm focal length, 330mm focal length
● Galvanometer speed
The mirror swing speed is adjustable. The X mirror is 50HZ at the
fastest and 50/30 per gear. The Y mirror is 200HZ at the fastest
and 200/30 per gear.
● Laser frequency
Laser pulse frequency, 1K-200K optional.
● Laser power
Laser output power can be adjusted from 1 to 100.
● Laser pulse width
Use it while using a adjustable pulse width laser machine
● Graphic length (laser pattern is square)
The length of the laser beam. The maximum length is 120MM, and the
length can be adjusted freely within 0-120mm range.
● Graphic width (laser pattern is square)
The width is up to 4MM, and the width can be adjusted freely within
0-40mm range.
● Filling pitch
The distance between lasers while cleaning with a circular laser.
● Opening delay and closing delay
When the laser galvanometer speed is too fast and the graphic
length is too long, the ideal effect can be achieved by setting the
switching light delay.
● Outer circle radius (laser pattern is ring)
The max. outer radius of the graphic outer circle is 40 mm, and the
radius can be adjusted during the circular size. When the graph is
circular, the inner circle radius is set to 0.
● Inner circle radius (laser pattern is ring)
The figure is a ring, and the radius of the inner circle can be set
up to 40MM (but not larger than the radius of the outer circle). In
this range, the radius can be adjusted to change the ring size.
● Application
While parameters were set in the interface. If you enable this set
of parameters, click Application.
● Save
After set the parameters in the interface, remember to click “Save”
to save the parameters for the next direct use.
● Red light
When the button is pressed, the red button turns red and the red
light comes out. Press again and the red button will return to gray
and turn off the red light.
● Laser
Laser light button, press the button, the laser light comes out. If
the red light is emitted at this time, the laser will be forced
out. Press the laser button again to turn off the laser light and
the button will return to gray.
● Group
Mode selection, you can save nine sets of data. Click on the number
on the left side of the mode, you can select the set mode
parameters freely, click on the application. Remember to save the
data after the parameter wat set in each interface.
