Electromagnetic Flow Meter with SS304 PFA Liner for Tap Water /
Juice / Milk / Coca Cola / Beer
1. Introduction
MLF electromagnetic flow meter, composed of sensor and converter,
works based on Faraday’s law of electromagnetic induction law. It
is used to measure electrical conductivity of liquid or solid.
Generally, the electrical conductivity should be over
5υS/cm(electrical conductivity of tap water, raw water is about
100～500υS/cm),It can also be used to measure various media like
acid, alkali, saline solution, paper pulp or pulp and so on. But
these media can’t contain a lot of magnetic materials and bubbles.
MLF electromagnetic flow meter is a kind of instrument which is
used for measuring the flow conductivity liquid. The meter is
widely used in flow measuring of Metallurgy, Chemical Industry,
Paper Industry,Environmental Protection, Oil Industry, Textile
Industry, Food Industry and City Administration, Water Works,etc.
2. Application:
MLF electromagnetic flow meter is a kind of instrument,used for
measuring the flow conductivity liquid, which is widely used in
flow measuring of Metallurgy, Chemical industry, Paper industry,
Environmental protection, Oil industry, Textile industry, Food
industry and City administration, Water works,etc
3. Quick Details
MLF electromagnetic flowmeter is explosion-proof design.
Low conductivity measurement function.
There are nine language options to meet the needs of different
customers.
It has self-regulation function and self-test.
Different outputs are optional: Hart, RS485, Profibus, 4-20mA,
frequency, pulse.
4. Specification
| MLF Type | Divided Type | Integrated Type | Explosive Proof Integrated Type | Battery Powered Type | Heat Energy Type |
| Accuracy | ±0.2% or ±0.5% |
| Pipeline Diameter | DN10-DN2000 | DN10-DN600 | DN25-DN2000 |
| Flange | GB, ANSI, JIS, BS, Others |
| Pressure | DN10-DN600 1.0 1.6 2.5 4.0MPa |
| DN700-DN2000 0.6 1.0 1.6MPa |
| Liner Material | CR, PTFE, PU, Hard Rubber, PFA, FEP(F46) |
| Conductivity | ≥5µs/cm(Please contact us if it is less than 5µs/cm) |
| Electrode | 316L SS, Hb, Ta, Ti, Hc, Tungsten Carbide, Others |
| Protection Class | IP65, IP66, IP67, IP68 |
| Medium Temperature | -25~180℃
(Please refer to liner material) | -25~80℃(Please refer to liner material) | -25~180℃
(Please refer to liner material) |
| Ambient Temperature for Accuracy Influence | <±0.1%/10℃ or <±0.25%/10℃ at the ambient temperature of -25~60℃ |
| Repetability | ≤±0.1% or ±0.25% |
| Analog Output Error | ≤±0.02mA |
| Velocity | 0.3~10m/s |
| Electrical connection | M20x1.5 Seal Cartridge, GB1/2, NPT1/2 |
| Output | 4-20mA, Pulse, RS485, Hart, Profibus |
5. Dimensional Sketches
a. Dimension of Converter
Divided Type
Integrated Type
Battery Powered Type
b. Dimension of Sensor
| Pipeline Diameter | Dimension |
| L | W | H |
| 15 | 160 | 95 | 130 |
| 20 | 160 | 105 | 137 |
| 25 | 160 | 115 | 150 |
| 32 | 160 | 135 | 160 |
| 40 | 200 | 145 | 175 |
| 50 | 200 | 160 | 185 |
| 65 | 200 | 180 | 205 |
| 80 | 200 | 195 | 215 |
| 100 | 250 | 215 | 235 |
| 125 | 250 | 245 | 275 |
| 150 | 300 | 280 | 300 |
| 200 | 350 | 335 | 355 |
| 250 | 400 | 400 | 405 |
| 300 | 500 | 455 | 460 |
| 350 | 500 | 515 | 520 |
| 400 | 600 | 575 | 580 |
| 450 | 600 | 635 | 630 |
| 500 | 600 | 710 | 685 |
| 600 | 600 | 835 | 795 |
| 700 | 700 | 905 | 910 |
| 800 | 800 | 1020 | 1030 |
| 900 | 900 | 1120 | 1120 |
| 1000 | 1000 | 1245 | 1250 |
| 1200 | 1200 | 1465 | 1470 |
6. Instrument Detection & Maintenance
The electromagnetic Flowmeter has the function of self-diagnosis.In
addition to power supply and hardware circuit failures, the system
also gives an alarm to other faults in general use.These messages
are prompted in the lower right corner of the screen.
1 Maintenance and repair.
A) the sensor installation site should meet the requirements of
Section 4, please keep the shell clean and tidy.
B) the transmitter should be placed in a clean, ventilated and dry
place.
C) it needs to be checked every two years, and for high-precision
users, the instrument needs to be submitted for review.
2 Transportation and storage.
A) the equipment must be packed before transportation and handled
carefully during loading and unloading.
B) the storage place must be dry and ventilated to avoid the
erosion of corrosive gases and the ambient temperature should not
be too low or too high.
C) the storage time should not exceed three years.
3. Out-of-the-box inspection.
A) the package cannot be opened with a heavy hammer, be careful not
to damage the instrument.
B) carefully check the contents according to the packing list.
