60KM SFP+ TX1330DFB Laser RX1270nm Optical Transceiver Module
10Gbps BIDI LC
Applications
| 10GBASE-BX |
| 10GBASE-LR at 10.3125Gbps |
| 10GBASE-LW at 9.953Gbps |
| Other Optical Links |
PRODUCT FEATURES
Up to 40km on 9/125um SMF
perating case temperature: 0 to 70 °C
ll-metal housing for superior EMI performance
Low power consumption, less than 1.5w
10Gb/s serial optical interface compliant to 802.3ae 10GBASE-ER/EW
Electrical interface compliant to SFF-8431 specifications for
enhanced 8.5 and 10 Gigabit small form factor pluggable module
“SFP+”
1330nm DFB transmitter ,1270nm PIN-TIA
Advanced firmware allow customer system encryption information to
be stored in transceiver
Cost effective SFP+ solution, enables higher port densities and
greater bandwidth
2-wire interface for management specifications compliant with SFF
8472 digital diagnostic monitoring interface for optical
transceivers
PRODUCT DESCRIPTION
The SFP+10G modules offer customers a wide variety of 10 Gigabit
Ethernet connectivity options for data center, enterprise wiring
closet, and service provider transport applications.It is a mallest
10G form factor Supports 10GBASE Ethernet and OTU2/OTU2e .
The SFP+10G module electrical interface is compliant to SFI
electrical specifications. The transmitter input and receiver
output impedance is 100 Ohms differential. Data lines are
internally AC coupled. The module provides differential termination
and reduce differential to common mode conversion for quality
signal termination and low EMI. SFI typically operates over 200 mm
of improved FR4 material or up to about 150mmof standard FR4 with
one connector.
SFP+10G modules Complaint with IEEE 802.3ae 10GBASE-LR,Electrical interface
compliant to SFF-8431 specifications for enhanced 8.5 and 10
Gigabit SFP module “SFP+”,1330nm DFB transmitter, PIN
photo-detector,LC connector,2-wire interface for management specifications
compliant with SFF 8472 digital diagnostic, Compliant with SFF8472
Digital Diagnostic Standard(DDM)
Optical module also be called optical fiber module, the translation
should be transceiver module. The function of the optical module is
the photoelectric conversion, and the transmitter converts the
electrical signal into the optical signal. After the transmission
through the optical fiber, the receiving end converts the optical
signal into the electrical signal. SFP is a kind of optical module.
Optical fiber module classification: according to function:It
includes optical receiving module, optical transmitting module,
optical transceiver module and optical transmitting module
Specifications
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Notes |
| Maximum Supply Voltage | Vcc3 | -0.5 | - | 4.0 | V | |
| Storage Temperature | TS | -40 | - | 85 | °C | |
| Operating Humidity | - | 5 | - | 95 | % | |
| Maximum Supply Voltage | Vcc3 | -0.5 | - | 4.0 | V | |
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Notes |
| Power Supply Voltage | Vcc | 3.13 | 3.30 | 3.47 | V | |
| Power Supply Current | Icc | - | - | 300 | mA | |
| Case Operating Temperature | Top | 0 | - | 70 | °C | |
| Data Rate | - | - | 10.3125 | - | Gb/s | |
| 9/125um G652 SMF | Lmax | - | - | 20 | Km | |
Spec
| Parameter | Symbol | Min | Typ | Max | Unit | Ref. |
| Transmitter |
| Output Opt. Power | PO | 0 | | 5 | dBm | |
| Side-Mode Suppression Ratio | SMSR | 30 | | | dB | |
| RMS Spectral Width(-20dB) | σ | | | 1 | nm | |
| Optical Extinction Ratio | ER | 3.5 | 4.5 | | dB | |
| Tx Jitter(SONET)20KHZ-80MHZ | Txj1 | | | 0.3 | UI | 3 |
| Tx Jitter(SONET)4MHZ-80MHZ | TXj2 | | | 0.1 | UI | 3 |
| Path penalty at 800ps/nm@9.95Gb/s | | | | 2 | dB | |
| Relative Intensity Noise | RIN | | | -128 | dB/Hz | |
| Center Wavelength | λc | 1320 | 1330 | 1340 | nm | |
| Receiver |
| RX Sensitivity @10.3 Gb/s | SENS | | | -16 | dBm | 1,2 |
| Receiver Overload | | -1 | | | dBm | |
| Optical Center Wavelength | λC | 1260 | 1270 | 1280 | nm | |
| LOS De-Assert | LOSD | | | -17 | dBm | |
| LOS Assert | LOSA | -30 | | | dBm | |
| LOS Hysteresis | | 0.5 | 2 | 6 | dB | |
Notes:
1. Measured with conformance signals defined in FC-PI-2 Rev. 10.0
specifications.
2. Measured with PRBS 231-1 at 10-12 BER.
3. GR-253-CORE Issue 4.
4. With optical input power at the receiver between -1 ~ -11dBm
