EN10305-2 E235 E355 Welded Cold Drawn Carbon Steel Tube
With high dimension accuracy and fine surface quality, cold drawn
precision steel tubing is suitable for using hydraulic and
pneumatic systems. Besides seamless cold drawn tubes, welded cold
drawn tubes is also used for cylinder with a smooth surface. BS EN
10305, a series of steel tube specification for precision
applications, 10305-2 grade E235 is a ideal material for barrel and
cylinder.
Corresponding standards: DIN 2393 St 37-2
size range :O.D. 50 - 380 mm; W.T. 1 - 25 mm
Length: 5 - 7 m
Application: Vehicle construction, furniture industry and general
engineering.
E235 Chemical Composition
| Steel grade | Steel number | C max | Si max | Mn max | P max | S max | Al min |
| E235 | 1.0308 | 0,17 | 0,35 | 1,20 | 0,025 | 0,025 | 0,015 |
E235 Mechanical properties under delivery condition +C (Room
Temperature)
| Steel grade | Tensile strength Rm MPa | Yield strength ReH MPa | Elongation % |
| E235 | 520 | 470 | 10 |
BS EN 10305-2 E235 Surface condition:
A roughness value of Ra < 0,8 μm applies to the inside surface,
in compliance with ISO 4287 and ISO 4288. For the outside surface,
en 10305-2 is applicable
BS EN 10305-2 E235 Straightness:
Tubes for hydraulic and pneumatic applications are specially
straightened with regard to the intended application. For tubes
with an outside diameter D > 15 mm supplied in lengths greater
than 1 000 mm, the deviation from straightness of any tube length L
shall not exceed:
a) 0,001 5 L for ReH ≤ 500 MPa ;
b) 0,002 L for ReH > 500 MPa
SHEW-E STEEL manufactured a wide range of cold drawn welded pipe
products with excellent quality and services for tube related
solutions. We offers specially precision steel tubes with outside
diameters from 50 to 380 mm and wall thicknesses up to 25 mm to
suit a wide range of applications.
Production Method:
The cold drawn welded tube is produced by drawing ERW (electric
resistance welded tube).During this process the sizing (wall
thickness, inside and outside diameter), as well as weld integrity
and surface finish is closely controlled to produce tube of the
required size and mechanical property characteristics.
Main Date
Material: E355
Other Aviliable Material: E155 E195 E235 E275
Outer Diameter Range: 10-50mm
Wall Thickness Range: 1.5-8mm
t/D ≥ 0.2(Normal: t/D=0.1)
Standard: En10305-2
Process: Cold Drawn, Cold Rolling
Typical Specification
| Grade |
Welding Typical Specification |
Yield Strength |
| 1 | E355 | Φ38×4.5 | 355~450Mpa |
Chemical Component
| Steel Number | Quality Level | Thickness/mm | Deoxidize Method | C(%)≤ | Si(%)≤ | Mn(%)≤ | P(%)≤ | S(%)≤ |
| E185(Fe310) | 0 | - | - | - | - | - | - | - |
| E235(Fe360) | A
B
C
D | ≤16
>16-25
≤40
>40
| N
-
-
E
NE
NE
GF | 0.22
0.17
0.20
0.17
0.20
0.17
0.17 | -
0.40
0.40
0.40
0.40
0.40
0.40 | -
1.40
1.40
1.40
1.40
1.40
1.40 | 0.050
0.045
0.045
0.045
0.045
0.040
0.035 | 0.050
0.045
0.045
0.045
0.045
0.040
0.035 |
| E275(Fe430) | A
B
C
D | ≤40
>40 | -
E
NE
NE
GF | 0.24
0.21
0.22
0.20
0.20 | -
0.40
0.40
0.40
0.40 | -
1.50
1.50
1.50
1.50 | 0.050
0.045
0.045
0.040
0.035 | 0.050
0.045
0.045
0.040
0.035 |
| E355(Fe510) | C
D | ≤30
>30
≤30
>30 | NE
NE
GF
GF | 0.20
0.22
0.20
0.22 | 0.55
0.55
0.55
0.55 | 1.60
1.60
1.60
1.60 | 0.040
0.040
0.035
0.035 | 0.040
0.040
0.035
0.035 |
Delivery Condition:
1) +C No heat treatment after the final cold drawing process.
2) +LC After the final heat treatment there is a suitable drawing
pass.
3) +SR After the final cold drawing process there is a stress
relieve heat treatment in a controlled atmosphere.
4) +A After the final cold drawing process the tubes are annealed
in a controlled atmosphere.
5) +N After the final cold drawing operation the tubes are
normalized in a controlled atmosphere.
Advantage (compare with seamless cold drawn tube)
Better shape
Improved quality surface
Tight Excentricity and wall thickness tolerances (the eccentric
Tube more safety
Good toughness at low temperature
USA Market: 90% of the cylinder in the USA market are produced with
welded tubes
Cost fix Lengths More Cheaper
Advantage of Our Company
Top class of welding line: SG/76 Enhanced High-precise High
Frequency Welding Tube Production Line. The tube is of small outer
diameter (D) and thick wall thickness (t): t/D≥0.2, and high size
precision.
