ASME B16.48 Hastelloy B3 Forged Spectacle Blind Spacer Ring Paddle Blind

1.Alloy B2 & B3 Machining Data

Suggested starting rates:

2.Dimensions Spectacle Blinds - ASME B16.48

Pressure Class 150

NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W
1/2	45	16	60	3	38
3/4	54	21	70	3	38
1	64	27	80	3	38
1.1/4	73	42	90	6.4	38
1.1/2	83	48	100	6.4	38
2	102	61	120	6.4	51
2.1/2	107	73	140	6.4	51
3	133	89	150	6.4	64
3.1/2	159	102	175	9.7	64
4	172	114	190	9.7	64
5	194	141	215	9.7	76
6	219	168	240	12.7	76
8	276	219	300	12.7	76
10	337	273	360	15.7	102
12	406	324	430	19.1	102
14	448	356	475	19.1	108
16	511	406	460	22.4	108
18	546	457	580	25.4	114
20	603	508	635	28.4	121
24	714	610	750	31.8	140
NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W

Pressure Class 300

NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W
1/2	51	16	65	6.4	38
3/4	64	21	80	6.4	38
1	70	27	90	6.4	38
1.1/4	79	42	100	6.4	38
1.1/2	92	48	115	6.4	38
2	108	61	125	9.7	51
2.1/2	127	73	150	9.7	51
3	146	89	170	9.7	64
3.1/2	162	102	185	12.7	64
4	178	114	200	12.7	64
5	213	141	235	15.7	76
6	248	168	270	15.7	76
8	305	219	330	22.4	76
10	359	273	385	25.4	102
12	419	324	450	28.4	102
14	483	356	515	31.8	108
16	536	406	570	38.1	108
18	594	457	630	41.1	114
20	651	508	685	44.5	121
24	772	610	810	50.8	140
NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W

Pressure Class 600

NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W
1/2	51	16	65	6.4	38
3/4	64	21	80	6.4	38
1	70	27	90	6.4	57
1.1/4	79	37	100	9.7	57
1.1/2	92	43	115	9.7	67
2	108	55	125	9.7	57
2.1/2	127	67	150	12.7	67
3	146	83	170	12.7	67
3.1/2	159	96	185	15.7	76
4	191	108	215	15.7	76
5	238	135	265	19.1	86
6	264	162	290	22.4	86
8	318	212	350	28.4	95
10	397	265	430	35.1	105
12	454	315	490	41.1	105
14	489	346	525	44.5	114
16	562	397	605	50.8	124
18	610	448	655	53.8	133
20	679	497	725	63.5	133
24	787	597	840	73.2	152
NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W

Pressure Class 900

NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W
1/2	60	16	80	6.4	38
3/4	67	21	90	6.4	41
1	76	27	100	6.4	57
1.1/4	86	37	110	9.7	57
1.1/2	95	43	125	9.7	67
2	140	55	165	12.7	57
2.1/2	162	67	190	12.7	67
3	165	83	190	15.7	67
4	203	108	235	19.1	76
5	244	135	280	22.4	86
6	286	162	320	25.4	86
8	356	212	395	35.1	95
10	432	265	470	41.1	105
12	495	315	535	47.8	105
14	518	346	560	53.8	114
16	572	397	615	60.5	124
18	635	448	685	66.5	133
20	696	497	750	73.2	133
24	835	597	900	88.9	152
NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W

Pressure Class 1500

NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W
1/2	61	16	80	6.4	38
3/4	67	21	90	9.7	41
1	76	27	100	9.7	64
1.1/4	86	35	110	9.7	64
1.1/2	95	41	125	12.7	70
2	140	53	165	12.7	70
2.1/2	162	63	190	15.7	76
3	172	78	205	19.1	76
4	206	102	240	22.4	89
5	251	128	290	28.4	89
6	279	154	320	35.1	89
8	349	203	395	41.1	102
10	432	255	480	50.8	114
12	518	303	570	60.5	114
14	575	333	635	66.5	127
16	638	381	705	76.2	133
18	702	429	775	85.9	146
20	752	478	830	95.3	152
24	899	575	990	111.3	178
NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W

Pressure Class 2500

NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W
1/2	67	16	90	9.7	38
3/4	73	21	95	9.7	41
1	83	27	110	9.7	64
1.1/4	102	35	130	12.7	64
1.1/2	114	41	145	15.7	70
2	143	53	170	15.7	70
2.1/2	165	63	195	19.1	76
3	194	78	230	22.4	76
4	232	102	275	28.4	89
5	276	128	325	35.1	89
6	314	154	370	41.1	89
8	384	198	440	53.8	102
10	473	248	540	66.5	114
12	546	289	620	79.2	114
NPS	Outside Ø A	Inside Ø B	Center Line C	THK t	Web Width W

General notes:

• Dimensions are in millimeters unless otherwise indicated.
• D = Hole size (where required) should be the same as the flange bolt hole. In practice, these dimensions have been rounded round off upwards.
• Wt = Thickness of the web (or tie bar) should be 6 mm minimum, or equal to Thickness (t) if less than 6 mm.
• Spectacle Blinds should be made from a plate or forging specification, approved for use by ASME B31.3, of essentially the same chemical composition as the mating flanges and piping involved.
• Spectacle Blinds ASME B16.48 may be used for installation between ASME B16.5 flanges
• Depending on a customer specification, some dimensions can be different from what on this page is defined.

Remark(s) of the Author...

Raised Face Joint Blanks

• ASME B16.48 says: The gasket seating surface finish and dimensions for raised face line blanks shall be in accordance with ASME B16.5. A raised face may be specified at the option of the purchaser.
• A Raised Face would add machining time and complexity so the price would be higher. Call this the Bugatti or Rolls Royce of the line blind world.
• Personally, I have seen that version once or twice somewhere. The version without Raised Face is the default and is used everywhere.

Huitong Group was established in 1978. After 38 years'development and innovation,by now,Huitong Group has set up multiple subsidiary companies.Among them,Zhengzhou Huitong Pipe Fitting Co.,Ltd.,with the indepent right of import and export, is mainly engaged in exporting steel pipe and pipe fittings for Huitong Group and assisting another subsidiary company of Huitong Group:Zhengzhou Huitong Machanical Equipment Co.,Ltd., in exporting machanical equipment.

Zhengzhou Huitong Pipeline Equipment Co.,Ltd.,with the strong support of Huitong Group,and years'development and innovation, are more and more professional in technical service and can manufacure products with all kinds of material,shape and size. Especially in elbows, tee, reducer, flange and pipe cap etc., we have gained more than 20 product patent, and hundreds of technology patent. Also,we have gradually taken an ireplacable role in High-pressure,high-temperature and anti-corrosion area. With the continuous construction of engery in China,such as petrol gas,electric power,etc.,our company has become the purchasing center of whole set fittings for such projects.In 2009,a foreign trade team established,is manily engaged in oil gas and electric power projects abroad.By now, our products have been exported to

Canada,Malaysia,Parkistan,UAE, Eygpt,the Middle East countries, etc.. We have passed the qualification of ISO9001:2000 and API quality certification system. High-quality products and high-class service are well received by abroad customers in this industry. The unique diversified production line can offer you one-package serive, you can pruchase all complex products from us at one time. What's more, our sufficient material stock and conventional product stock can ensure you receive satisfied product in the shortest time.

With powerful financial strength,advanced managerial concept, excellent marketing service,strict quality control system and integrated marketing team,we would like to develop together with you hand in hand. Adhering to the operation principle of "faith first and clients foremost", we always supply high quality products, complete after-sales service and favorable prices. We sincerely hope to establish long-term cooperation with you on the basis of mutual benefits, reciprocity and common development.

People who interested in our products or want to get more information about us,contact us,please!Looking forward for your inquiry.