Hyno energy. Original Factory HEV Battery Replacement Fit For Lexus
RX450H (2010-). 6500mAh 288V, guaranteed performance
SCOPE
This specification is applicable to Ni MH battery for hybrid
produced by Hunan Hi-soon Supply Chain Co., Ltd.,
Model: Hyno RX450H 288
Suitable for: Lexus RX450H (2010-).
RATINGS
| No. | Description | Unit | Specification | Condition |
| 1 | Nominal Voltage | V | 288 | |
| 2 | Operating Voltage | V | 204.0～326.4 | |
| 3 | Nominal capacity | mAh | 6500 | Standard charge / discharge |
| 4 | Minimum capacity | mAh | 6000 | Standard charge / discharge |
| 5 | Nominal Energy | Wh | 1728 | 1 hour rate |
| 6 | Weight | Kg | 35±0.1 | Standard environment,Accuracy±0.05g Electronic scale |
| 7 | Power Density | W/kg | ＞850 | |
| 8 | Energy Density | Wh/kg | ＞43 | |
| 9 | Max. continuous discharge current | C | 20 | 20℃～45℃ |
| 10 | Max. continuous charge current | C | 15 |
| 11 | Storage Temperature | ℃ | -20～35 | |
| 12 | Operating Temperature | ℃ | -30～55 | |
PERFORMANCE module only
Tests should be done within one month of receiving the goods under
the following conditions.
Test condition
Temperature:20±5℃
Relative Humidity:65±20%
Atmospheric Pressure:86～106kPa
Standard charge discharge specification
Discharge: 6000mA (1C) to 168.0V
Charge: 6000mA (1C)×1hrs,1200mA (0.2C)×1hrs
Discharge: 6000mA (1C) to 12.0V
| No. | Test | Unit | Description | Condition | Note |
| 1 | Open circuit voltage (OCV) | V | ≥15 | Within 1h after charging | |
| 2 | Internal resistance (DC-IR) | mΩ | ≤32 | 50%SOC | |
| 3 | Internal Impedance (AC-IR) | mΩ | ≤14.2 | 1kHz | |
| 4 | Self -discharge rate | % | ＜18 | | 55±2℃ rest 3days, 20±2℃ rest 7days |
| 5 | Energy Efficiency | % | ≥85 | 25℃ | |
| 6 | Volumetric Efficiency | % | ＞95 | 25℃ | |
| 7 | Cycle Life | Week | ＞3000 | 80%DOD | Charge to 90%, discharge to 10% |
GUARANTEE
Product fabrication and material defects are guaranteed within 2
years.
Recommendations: the company's products have been filled 30-90%
power in the factory, depending on the shipping distance and
packing conditions. When capacity measurement, discharge with 1C to
12.6V/ stick; then charge/discharge with the specified current to
test capacity. If the stock reach or exceed 2 months, discharge
with 1C to 14.4V/ stick; Then charge with 1C for 54min, 0.2C charge
for 1hrs, rest 20min, discharge with 1C to 12.6V/ stick, after 3
cycles; Then charge/discharge with the specified current to test
capacity.
For the first use, the standard charge method is recommended to
avoid damage to the battery.
CAUTION
When charging the battery, please charge in accordance with the
charging method in the product specification. Use the specified
charger in the specified temperature range. Do not reverse charge,
do not exceed the required charging current, and do not exceed the
required charging time. Do not charge only with limited voltage and
limited current
- Do not put the battery into the fire or heating it
- Do not connect the positive and negative pole with conductive
substances such as metals.
- Do not dissect the battery.
- Do not refit or damage batteries.
- Do not solder battery.
- Do not contacting the battery with water, sea water, or other
oxidants.
- Do not hit, puncture or shock battery.
- Do not use batteries inconsistent with the equipment.
- The inside strong alkali with high corrosiveness may burn people.
If alkali is hitting eyes, skin or clothing, please drastically
clean it with tap water or other clean water and get medical
treatment straight away.
- If the battery does not work properly in the equipment, please
refer to the equipment warning and use manual.
Appendix
Hunan Hi-soon Supply Chain Co., Ltd reserves the right to change
and revise Product specification without any advance notice.
