BS -500 Plastic Pulverizer Machine PP Pulverizer Machine For Grinding Flakes And Granules

BS-500 PP pulverizer machine for grinding flakes and granules with inverter

Plastic pulverizer machine introduction:

Suitable for PVC, PE, PET recycled materials. It is used for fine grinding of various plastics, especially for processing and grinding thermoplastic PVC PE plastic recycled materials. According to the practice of the professional factory of plastic products, the grinding powder is added in the processing formula by 20%-30%, and the chemical and physical properties of the products remain unchanged. Therefore, it is the best equipment for plastic products factory to reduce the accumulation of waste products....

There are several specific reasons that affect the material requirements of plastic mills that do not meet the requirements:

1: The main motor speed, the faster the main motor speed, the better the material discharge, the finer the mesh. http://www.beisu-extrusion.com Some customers adjust the main motor speed slowly, thinking that this can save electricity, which is a big misunderstanding. There is a speed ratio of the main motor pulley and the drive shaft pulley to be controlled within a reasonable range (normally not less than 3000 rpm).

2: The degree of wear of the blade, the new plastic mill will have different degrees of wear according to different materials after a period of use. If the user has uneven material thickness, the plastic mill should be inspected in time or Whether the fixed knife is worn or not, it should be repaired or replaced if it is seriously worn, so as not to affect the product quality and work efficiency.

3: The temperature of the material: the temperature of different grinding materials is different. When the user replaces the grinding material, pay attention to the type, batch and plasticizing performance of the grinding material, so as to control the temperature of the material through the water circulation of the cooling system. The material with too high temperature is relatively fine.

4: The size of the crushed material, the recycled material needs to be crushed by the crusher before grinding. The screen of the crusher is critical. The mesh size of the sieve should be replaced in time according to the actual condition of the material. The operator should according to the size of the crushed material. Supervision, timely observation of material size changes, to ensure that the broken material size is between 5-8mm.

zhangjiagang beisu machienry main mahine sales http://www.beisu-extrusion.com: plastic mill, PE mill, PVC mill, grinding disc mill, high-speed mixer, high-speed mixing unit, PVC mixer, high mixer

Details specification pictures of Plastic pulverizer:

Technical dates of Plastic pulverizer:

A1:PP/EVA/ABS pulverizer

A2:HDPE/LLDPE /soft PVC/PET etc pulverizer

A3:Hard PVC pulverizer:

Plastic mill safety matters:

Familiar with the contents of the manual and the function of the electrical button, the direction of rotation of the main unit must conform to the direction of the arrow marked on the belt cover.

Start the fan before starting the machine (pay attention to the steering). After the normal operation, start the main machine to reach the normal speed and start feeding.

At the beginning of production, the valve opening of the feeding port should be small, as long as the material can come out, then slowly open the damper cover. After the material enters the machine, the load condition of the machine is generally around 68A, which is measured by the ammeter on the electric control panel. The 37KW 4KW is parallel, so its total current value is 70A. During normal operation, the current should be between 65-70A and swing.

Material selection requirements: The maximum diameter of the material particles should not exceed 15mm. Do not accidentally enter the machine into the machine, so as to avoid intensifying the wear and damage of the blade and fixing the knife.

If there is abnormal sound during operation, stop immediately, open the door cover to check, and then continue production after the exclusion.

Plastic mill maintenance:

1 Open the door cover regularly, check the blade fastening nut, whether the cover and nut are loose, and tighten if loose.

2 Lubrication: The use of lithium-based disulfide (MoS2) grease for the main bearing

3 Fans and ducts shall inspect their blades and inner walls of the pipes and remove the dust from their knots.

4. After the blade has been used for a considerable period of time, the surface of the blade is ground to a larger radius.

Remove the blade splint and turn the blade 180 degrees. After tightening, continue to use.

BEISU Machinery:

BEISU machinery and equipment recommendation: PVC/PE/PP pipe production line, PVC/PE wood plastic production line, PVC profile/profile production line, PVC/PP/PE/ABS sheet/sheet production line, PVC edge band production line and mill, High-speed mixer , crusher, sharpener, shredder, tractor, winder, cutting machine and other plastic auxiliary machinery.

BEISU Machinery is a technical manufacturing plant specializing in the manufacture of plastic recycling、granulation、 shredding、crushing, grinding and mixing. The main equipment includes plastic extruder, plastic granulator, plastic shredder, plastic crusher, plastic pulverizer, plastic mixing equipment, plastic feeding system and other plastic extrusion recycling production equipment. Provide complete turnkey projects for waste plastics, pipes, profiles, plates, wood-plastic, rotational molding, dip-molding, color masterbatch, rubber, aluminum-plastic and other applications.

At present, the "BEISU" machinery brand has covered the world such as Thailand, the United States, Saudi Arabia, Bangladesh, Pakistan, the United Kingdom, Chile, Poland, India, Mexico, Russia, Nepal and so on. 

Why choose BEISU Machinery:
A1: Plant construction, renovation plan, pipeline laying plan in the plant, construction plan of circulating cooling pool

A2: Supply of raw materials, transformers, air compressors and other procurement plans

A3: Provide relevant raw material specific formula, high quality raw material suppliers, raw material cost accounting

A4: Installation equipment, commissioning equipment, training staff, and provide technical support throughout the year

A5: BEISU company has a plastics industry engineering alliance nationwide, in the case of distance, can provide relevant talents in your company year-round work, as a technology backing