Moulds Die Tools Automatic Ultrasonic Cleaning Equipment SS 304 Material 360l 28khz

360l 28khz Moulds Automatic Ultrasonic Cleaner Ultrasonic Cleaning Of Die Tools

Main benefits

• AGSONICGenius ultrasonic technology provides a powerful, digitally regulated cleaning effect.
• Flexible configuration possibilities ensure ideal solution for any cleanliness requirements.
• Designed with the operator in mind, there are no compromises with safety and high level of ergonomics is ensured.
• AGSONICprovides the Famous AGSONICdurability and reliability thanks to a service friendly and heavy duty construction.
• Robust technology ensures equipment with long operating life.
• Fully automatic lines with an intuitive control system and AGSONICNetService remote support are designed for your piece of mind.
• AGSONICOptima provides a wide range of options to improve process efficiency and to minimize environmental impact

Moulds Glass Industry Cleaning Plastic Injection Molds Automatic Cleaning Machine

How Ultrasonic cleaning machines working
Ultrasonic cleaning machines work on the principle of agitating cleaning solvents using high frequency sound waves, the ultrasonic agitation creates millions of microscopic bubbles that implode releasing vast quantities of energy, this action, know as cavitations, dislodges any contaminant stuck to the surface of a part, ultrasonic cavitations thoroughly cleans every surface in contact with the cleaning fluid

How to Clean Large Plastic Injection Molds

Complex molds require careful cleaning.

Complex injection molds represent substantial investments by plastic injection molding companies which, in order to protect their investments, must establish cleaning procedures to remove a variety of stubborn contaminants. These include burned on residues, oils, flashing and grease that if allowed to remain will result in product rejection by the quality control department. Hand scrubbing with solvents simply does not do the job. In addition to being time consuming, manual cleaning introduces potential health hazards for personnel and solvent disposal challenges. The solution is using an ultrasonic cleaner instead of scrubbing in a solvent-based parts washer.

Why an Ultrasonic Cleaner is Ideal for Injection Molding

In three words: thorough, safe and fast. Contaminants missed by manual cleaning are usually those deep in crevices and on other surfaces impossible to reach. Moreover, highly finished mold surfaces can be scratched or otherwise damaged by manual processes. Large molds can be difficult to maneuver, further risking damage during manual cleaning. And the longer it takes to clean the molds the greater the risk of damage.

Ultrasonic cleaning action solves all three issues.

It is thorough because it reaches all mold surfaces immersed in a biodegradable water-based ultrasonic cleaning solution. It is safe because while the cleaning action can be termed “violent” it occurs so fast that highly polished injection mold surfaces are not damaged during the cleaning process. By fast we mean 10 to 15 minutes although large complex molds may require a longer cleaning cycle.

Plastic Mold Cleaning by Cavitation Action

Cavitation action is described as the implosion of countless minute bubbles against surfaces of products immersed in the cleaning solution. Bubbles are created when generator-powered transducers bonded to the ultrasonic cleaner tank vibrate at ultrasonic frequencies measured in thousands of cycles per second or kilohertz (kHz).

Selecting the cleaning equipment is governed to a large extent by the size of molds being cleaned. Ultrasonic cleaners are available ranging from small benchtop units to industrial-sized floor-mounted equipment that can be fitted for automated cleaning and rinsing cycles. But do select a cleaner with a heater, timer and sweep mode.

The process is fairly straightforward regardless of equipment size. Here’s a simplified description that can be modified based on your specific operations:

1. Fill the ultrasonic cleaner with water but allow room for cleaning solution displacement due to the size of the molds being cleaned. Add the proper amount of biodegradable cleaning solution concentrate. Ask the scientists at Tovatech to recommend the correct formulation based on the type of contaminants you are removing and what the mold itself is made of.
2. When you are ready to clean place the injection molds in the cleaner basket. Take care that they do not contact each other. If you are cleaning large parts you may suspend them in the cleaning solution so they do not contact the tank bottom. Some industrial cleaners are equipped with bottom racks to support products being cleaned.
3. Set the heater to 65 C and timer from 10 to 60 minutes depending on the degree of contamination. Activate the sweep mode to assure uniform distribution of cavitation and promote uniform cleaning then lower the molds into the solution. With experience you will establish optimum cleaning conditions.
4. At the end of the cycle remove the molds and inspect. When satisfied, rinse them with fresh hot water and allow them to dry or blow them dry with compressed air. Note that intricate configurations and cavities may trap water that should be removed by adding an electric drying oven to your setup.

Rinsing tip: You’ll want to thoroughly remove cleaning solution residues. Complex shapes may call for a spray rinse or, in certain cases, rinsing by cavitation in an ultrasonic rinse tank.

3 Tank Injection Molds, Blow Molds Ultrasonic Cleaning Machine With Each Tank's Dimension 1000*700*700mm

Main Features

1) Tank materail is SUS304 with 2mm thickness, Human hand argon welded, Sturdy and durable resistance to high tempearture
2) 50W industrial transducers, outstanding cleaning effects
3) External ultrasonic generator
4) Power adjustable, choose different power according to different cleaning objects
5) Digital timer: 1~99hours timer adjustable. continious working for long time.
6) With memory function, no need to reset time and temperature every time.
7) 20~80C adjustable, 9KW heating panel, faster cleaning
8) Industry use power cord, more safer.
9) Can bear 50~100KG cleaning objects

10) Accessories: Machine with stainless steel basket, drainage, lid, movable castors.

Large Ultrasonic Cleaners

ULTRASONIC POWER
1 Must have adequate power to initiate and maintain cavitation under most work conditions.
2 If we try to introduce too much ultrasonic power into a tank a barrier will form at the liquid/radiating
surface interface that will block additional input power and will cause advanced cavitation erosion.
3 If we do not have adequate ultrasonic power initiating cavitation will be difficult, maintaining
cavitation will be difficult, and cleaning at best will be marginal. A low power level will also greatly
reduce the cleaning applications the tank will be able to perform.
4 When considering purchasing a special ultrasonic cleaning system for a specific cleaning application
FIRST Contact someone who is knowledgeable in ultrasonic design.
SECOND. Send a sample of the item to be cleaned to their testing lab for evaluation. THIRD. Request
information on tank design best suited for the application.

AG SONIC technology limited  Is dedicated to manufacturing systems of many types and styles which include small table-top systems, large single-tank systems for injection molds are other large parts, oil filter and metal tape washers, aerospace parts washers, multi-stage machines which include cleaning, rinsing, and drying, automation systems, and custom equipment designed specifically for your needs

Product offered:

● Household ultrasonic cleaner

● Tabletop ultrasonic cleaner (mechanical series, digital series, power adjustable series)

● Industrial standard ultrasonic cleaning machine

● Customized ultrasonic cleaning machine

Service offered:

Our customers Are Our Focus

We are committed to understanding and interpreting the complex demands of our customers. By ensuring we have complete control of all our processes, we have the flexibility to provide cleaning solutions to meet individual customer requirements and standard to delivering innovative ultrasonic cleaning solutions to meet your requirements. We forge long lasting relationships with our customers and distributors, generating superior and robust partnerships.

Our Market:

We sell ultrasonic machines to worldwide countries, and our professional team will offer you the best after-sales service. We believe after-service is as important as quality and price.