NEW ORIGINAL 5.4A 750W Servo Motor Industrial Yaskawa Servo Motor
SGMPH-01BBA21
DESCRIPTION
Current: 0.89A
Volatge: 200V
Power :100W
Rated Torque: 0.318-m
Max speed: 3000rpm
Encoder: 17bit Absolute encoder
Load Inertia JL kg¡m2¢ 10−4: 0.026
Shaft: straight without key
SEPCIFICATIONS
| Manufacturer | Yaskawa / MagneTek / Saftronics / Omron |
| Series | Sigma 2 (Σ-II Series) |
| Weight | 10KG |
NOTE
- After turning the power OFF, do not touch the power terminals for 5
minutes. High voltage may remain in the Servopack.
- Avoid frequently turning the power ON and OFF. Since the Servopack
has a capacitor in the power supply, a high charging current flows
(for 0.2 second) when the power is turned ON. Therefore, frequently
turning the power ON and OFF causes the main power devices (such as
capacitors and fuses) to deteriorate, resulting in unexpected
problems.
- If the Servopack is turned ON immediately after being turned OFF, a
power loss alarm may arise. To prevent this, always wait for the
time shown in the following table before turning the power ON
again:
This sub-section provides typical examples of connecting to main
host controllers. Connection to other host controllers is also
possible. Connect to the host controller according to the
connection examples shown below by referring to technical
documentation for the host controller.
NOTE
This sub-section describes signals related to the SGDA Servopack
only.
For other signals, refer to the relevant technical documentation.
2) Example of Connecting to PROGIC-8
Test Run in Two Steps
Conduct the test run when wiring is complete. Generally, conducting
a test run for servo drives can be difficult , by following the two
steps described below, the test run can be performed safely and
correctly.
Check that the motor is wired correctly. If the motor fails to
rotate properly during a servo drive test run, the cause most
frequently lies in incorrect wiring. Conduct a test run for the
motor without load according to the procedure described below. For
customers who use a servomotor with brake, refer to Section 2.4.4
Supplemental Information on Test Run before starting a test run.
When a host controller such as a programmable controller performs
position control, it may be difficult to directly input the speed
reference voltage. In this case, constant voltage reference should
be input once to ensure correct operation.
SIMILAR PRODUCTS
| SGMPH-02A1A-YR12 | SGMPH-02A1A-YR21 |
| SGMPH-02A1A-YR31 | SGMPH-02A1A-YR32 |
| SGMPH-02A2A-YR12 | SGMPH-02A2A-YR21 |
| SGMPH-02AAA2B | SGMPH-02AAA2C |
| SGMPH-02AAA2E | SGMPH-02AAA2E |
| SGMPH-02AAA4B | SGMPH-02AAA61 |
| SGMPH-02BAA21 | SGMPH-02BAA41 |
| SGMPH-04A1A21 | SGMPH-02BAAG161 |
| SGMPH-04A1A2B | SGMPH-04A1A2C |
| SGMPH-04A1A41 | SGMPH-04A1A4B
|
Contact person: Anna
E-mail: wisdomlongkeji@163.com
Cellphone: +0086-13534205279
CAUTION
• Conduct trial operation on the servomotor alone with the motor
shaft disconnected from the machine to avoid any unexpected
accidents. If it is unavoidable to perform trial operation while
connected to a machine, then always make sure that an emergency
stop can be immediately executed.
• Conduct trial operations on the servomotor alone, with the motor
shaft disconnected from the machine to avoid accidents. Failure to
observe this caution may result in injury.
Servomotors with Brakes When performing trial operation using a
servomotor with a brake, use a brake interlock signal as shown
below.
A brake control relay can be installed on either the AC or DC side.
To reduce brake activating time, install it on the DC side. Be sure
to check the brake activating time before using it. When
opening/closing the brake power supply circuit relay on the DC
side, be sure to provide surge protectors both near the brake coil
and built in the brake power supply circuit to protect the brake
coil from damage due to surge voltage.
