Anti - Corrosion gravel Slurry Pump Rubber Liner Open Impeller Type 3 / 2 C - AHR

Anti - Corrosion gravel Slurry Pump Rubber Liner Open Impeller Type 3 / 2 C - AHR

Product overview

3/2C-AHR is horizontal, vertical open type, double pump housing structure, pump body and pump cover with replaceable rubber liner, the rubber liner can be used until wear-through no need to replace, extend the maintenance cycle and reduce operating costs.

The 3/2C-AHR slurry pump can transport strong abrasive slurry in the low flow and low lift area; it can transport light abrasive slurry in the high lift and large flow area. It is suitable for the transportation of strong abrasion and high concentration slurry in metallurgy, mining, coal, electric power, building materials and other industrial sectors.

This type of pump is a rubber pump. Its rubber lining has the ability to protect metal or other substrates from abrasion or erosion of various media. Various rubber linings are resistant to corrosion by acids, alkalis, inorganic salts and various organic substances. It also has good overall properties such as elasticity, wear resistance, impact resistance and adhesion of other substrates.

AH slurry pump start:

The entire unit should be inspected as follows before starting.

(1) The pump should be placed on a firm foundation to withstand the full weight of the pump to eliminate vibration and tighten all anchor bolts.
(2) Pipes and valves should be supported separately. There should be a gasket at the pump flange. When tightening the coupling bolt, please pay attention to the metal lining of the pump is higher than the flange. At this time, the bolt should not be tightened too much to avoid damage to the gasket.
(3) Rotate the shaft by hand according to the direction of rotation of the pump. The shaft should be able to drive the impeller to rotate and there should be no friction. Otherwise, the impeller clearance should be adjusted.
(4) Check the steering of the motor. Make sure that the pump rotates in the direction of the arrow marked on the pump body. Note that the pump is not allowed to rotate in the opposite direction, otherwise the impeller thread will trip, causing damage to the pump.
(5) When the transmission is directly connected, the pump shaft and the motor shaft should be accurately centered. When the belt is driven, the pump shaft and the motor shaft should be parallel, and the position of the sheave should be adjusted so as to be perpendicular to the groove to avoid severe vibration and wear.
(6) A detachable short pipe shall be installed at the suction pipe of the pump. The length shall be sufficient to disassemble the pump cover and replace the consumable parts, so as to facilitate the inspection of the pump. The length of each pump is shown in the external dimensions of each pump.
(7) Shaft seal inspection: The pump of the auxiliary impeller shaft seal has different sealing structure. Therefore, when the oil pressure cup is equipped with oil cup, it is necessary to add grease through the oil cup. The grease is recommended to be lubricated with calcium and sodium. fat.

3 /2 C - AHR Specifications

Typical Application

Minerals Flotation Processing
Electric Factory Coal Preparation
Coal Washing
Chemical Medium Processing
Effluent Handling
Sand And Gravel Handling

Tailings

Pulp and Paper

Standard Material of Wet-end Parts: Natural Rubber R55

Performance table of AH(R)/HH centrifugal slurry pump /Performance table

AH(R)/HH/M(R) Series Slurry Pump Construction Design

AH(R)/HH/M(R) Series Slurry Pump Construction Design

Shijiazhuang ShizaPump Industry Co.,Ltd. founded in 2008, is a professional industrial pump manufacturer engaged in researching slurry pump, wear and corrosion resistant materials and OEM processing.

Shizapump group covers more than 40000 square meters, the registered capital is 18 million yuan. Over the years with strong strength and people-oriented concept, we absorb a large number of high-quality management and technical talents. Existing staff is more than 220 people, of whom 30% are technicians.

Our production area covers an area of 24000 square meters, the total production capacity of an annual output is 10000 units (sets), and the annual output of all kinds of high chromium alloy castings is 2000 tons.The production area is divided into five districts one area and two centers, namely mould casting, heat treatment, fine machining, forge welding and assembly coating of five production areas; finished spare parts; quality analysis and water experiment. The main material of products: A05, A49, A33, A51 and other high chromium white cast iron.

Shijiazhuang ShizaPump Industry Co.,Ltd. fully implements the ISO9001 management system and observes the process of inspection. Quality inspection records are available in all production processes. Professional instruments include spectrometer, metallographic analyzer, flaw detector, mechanical test machine (strain, impact, hardness), magnetic flowmeter, pressure gauge, ammeter, vibration meter, noise meter, hydraulic experimental curve of professional software. Perfect detection guarantees the quality of equipment to ensure that each pumps and parts are fully in line with the requirements.

Shijiazhuang ShizaPump Industry Co.,Ltd. has spread all domestic market in China over 30 provinces and municipality. Also has been successfully used in 20 countries in global .First line staff have professional experience to provide service for customers.