30m/Min Copper Wire Cable Stripper Machine 1-50mm Diameter

30m/Min Copper Cable Stripper 1-50mm Wire Diameter Wire Stripping Machine

Description of wire stripping machine

Wire stripping machine has the most funtions among our stripper machines. It applies to various types of electric wires and cables, including copper wires, aluminum wires, steel wires, etc. Various rubber cables are easy to be stripped. Moreover, the cable stripper can strip single-core or twin-core flat wires at one time. The diameter range of cables that can be stripped is 2-120mm. The cutting speed is 30 m/minute.

The machine has totally 15 feeding holes for the wires, including 1 big and 1 small hole, 11 small round knife and 2 big round knife inlets for sheath wire, which can press out the metal in single-core wires directly.

Technical Parameters of wire stripping machine

Feature of wire stripping machine

1) Nice appearance, stable performance

2) This machine suitable for a variety of wire. Wire stripping range:2-120mm.This machine is practicable and easy to handle.

3) Frame dual blades principal, can process different diameter cable, easy to operate and durable.

4) This machine is easily to use, portable,energy saving and good looks,just like the normal stripper machine usage.

5) This model are easy to operate, convenient to carry, energy saving, for single copper wire(hard wires) can be rolled or blades stripping, other cables(soft wires) can be easily stripped.

Use direction of wire stripping machine

1. When start the machine, check that whether the operation is normal. When feeding, according to the size of the cable diameter, enter the corresponding feeding hole one by one.

2. In order to make the blade durable for a long time, the joint of rubber plastic cable should be cut off when feeding, so as to avoid the blade gap from collapsing.

3. If the feed is too deep and broken, pay attention to a few points

(1). The spring pressure on both sides of the feed gear and blade shaft should be adjusted.

(2). Check whether the position of feed hole is misplaced during feeding.

(3). If the blade is replaced, whether the edge is too sharp, use the grindstone to trim slightly until it is moderate

4. If after feeding, the skin has been stripped, but the copper wire can not be exposed, there are mainly the following situations.

(1). If the spring pressure is too loose, the pressure should be adjusted tightly.

(2). If the knurling of the upper shaft is too deep, the upper shaft should be polished with a grindstone, but it should not be grinded too much. Too much grinding will make it difficult for oily cables.

(3). If the cable diameter is too small or the gap between the upper and lower shafts is too large, adjust the clearance between the two shafts properly.

(4). The processed cable has been heated, the copper wire will not be easily exposed to the skin.

5. If the cable cannot be driven by the rolling gear after feeding, and the material stays in the middle, the following situations will occur.

(1). Check whether the belt of each gear is loose.

(2). Check whether the spring pressure on both sides of each gear is too tight and there is no jacking force. The pressure should be relaxed.

(3). Too much oil in cable leads to slipping of two shafts. Clean the two shafts frequently.

Henan TMS Machinery Co, Ltd is located in Zhengzhou city, Henan province, China. We are specialized in manufacturing the scrap metal recycling equipment, such as copper wire granulator, copper wire stripping machine, scrap metal baler, radiator recycling machine, motor stator recycling machine, metal shearing machine, dual shaft shredder, blade sharpener machine etc.

Our company process professional sales group, technical engineer and perfect after-sales team. We firmly believe that quality is the only standard for enterprises to survive. The quality of products we manufactured is superior. And our engineer will provide professional technical analysis and recommend suitable equipment to customers. At that time, to make client use our machine without any worries, best after-sales service is also supplied to everyone. Our after-sales person will follow your order in 24 hours.

By now, our machines are sold to all over the world. Just like Europe (France, US, Poland, Norway, Spain, Malta, Czech Republic, Italy etc), Americas(USA, Canada, Mexico, Brazil, Colombia etc), Australia(Australia, New Zealand), Asia(Thailand, Korea, India, Pakistan, Singapore, Malaysia, Sri Lanka, Saudi Arabia, Indonesia, Qatar, Dubai), Africa(Morocco, Ghana, Tanzania). In our factory, there are many advanced manufacturing facilities and almost 50 experienced workers, we have ability to produce 100-200 sets machine and 50 sets large production line per month. We can meet customers’ demand for kinds of recycling equipment.

Our company business aim is that Credit first, customer first, quality satisfaction, delivery on time, and willing to cooperate with you sincerely, development hand in hand. In the future, we will adhere to the company's philosophy and continue to provide customers with better products and quality services. With Joint efforts of our team, we can make our company bigger and stronger.