Iron Double Convoluted Air Spring Actuator Airkraft 113053/2B-181
Replacement With G3/4 Rubber Bellows For Vibration
Refer No.
Contitech FD120-17
Contitech FD12017
Contitech FD120 17
Contitech FD 120-17
Contitech FD 120 17
Contitech FD 12017
Airkraft:113054
Airkraft:2B-181
Airkraft:2B 181
Specifications and Detailed Technical Parameters: 2B12017-34
Top plate screw (nut) teeth: 2×M8×1.25
The screw center distance on the top plate: 70mm
Screw (nut) teeth of the bottom cover plate: 2×M8×1.25
The screw center distance on the bottom plate: 70mm
- Air hole/air inlet/air fittings
Air hole/air inlet/air fittings: G3/4
Air hole location: middle
The Diameter Of The Top Plate: 135 mm
The Diameter Of The Bottom Cover: 135mm
MAX. Rubber Bellow Diameter: 215mm
Height: 167mm
Working stroke: 75-230mm
- Bumper block/bumper block
Without bumper block
- Belt loop/Belt loop/Girdle hoop
With one piece of belt loop/girdle hoop
Min. pressure: 0 bar
Return force to min.height: ≤200N
Overall weight with clamped plates: 2.3kg
Vibration isolation - dynamic characteristic values
Design Height H: recommended 190mm, minimum 175mm
| Pressure p[bar] | 3 | 4 | 5 | 6 | 7 | 8 | Vol. V[l] |
| Force(Load) [KN] | 3.8 | 5.2 | 6.5 | 8.0 | 9.3 | 10.6 | 3.2 |
| Spring rate [N/cm] | 600 | 830 | 1060 | 1290 | 1520 | 1750 |
| Natural frequency [Hz] | 2.1 | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 |
Pneumatic application-static characteristic values
Force F[KN]
| Pressure p [bar] | 3 | 4 | 5 | 6 | 7 | 8 | Vol. V [l] |
| Height H[mm] | 200 | 3.4 | 4.8 | 5.9 | 7.3 | 8.5 | 9.7 | 3.4 |
| 180 | 4.2 | 5.7 | 7.1 | 8.6 | 10.1 | 11.5 | 3.1 |
| 160 | 4.9 | 6.5 | 8.1 | 9.9 | 11.5 | 13.1 | 2.8 |
| 140 | 5.5 | 7.2 | 9.1 | 11.0 | 12.7 | 14.5 | 2.4 |
| 120 | 6.0 | 7.9 | 9.9 | 12.0 | 14.0 | 15.8 | 2.1 |
| 100 | 6.4 | 8.5 | 10.7 | 12.9 | 15.1 | 17.0 | 1.6 |
| 80 | 6.8 | 9.1 | 11.3 | 13.7 | 16.0 | 17.9 | 1.2 |
Other Types Airkraft Replacement We Could Offer
| Guomat Model Size | Airkraft |
| 2B7894 | 113549 |
| 2B7180 | 115061/3B-356 |
| 2B12017-14 | 113054/2B-181 |
| 3B10×3 | 115056 |
| 3B7808 | 115061/3B-356 |
Reasons for the application of rubber air springs in vibration
equipment
1. Reduce the operating frequency. The greater the stiffness of the
rubber air spring material, the greater the stiffness of the air
spring, and the higher the first-order resonance frequency, which
increases the minimum operating frequency of the system. Therefore,
the rubber safety air spring vibration isolation system should
reduce the material stiffness and natural frequency, so that the
bearing capacity of the air spring vibration isolator can be
retained enough, and the minimum operating frequency of the system
should be as low as possible.
2. The comprehensive isolation effect is strong. When the vibrating
table vibrates laterally, the rigidity of the rubber material of
the reed capsule is much larger, the rubber air spring body has a
soft structure, and has a comprehensive vibration isolation effect
of axial, lateral and rotational steering, and a throttling is set
between the air spring and the additional air chamber. valve hole.
When air flows through the throttle hole, part of the vibration
energy is absorbed due to resistance, which acts as damping and
damping.
The related picture of 2B12017-34
