M1C Water Heater Magnesium Anode Rods Travel Trailer Camper Heat Tank Water Heater Anode

M1C High Potential Water Heater Magnesium Anode Rod Travel Trailer Camper Heat Tank Water Heater Anode

Introduction of anode rods for protection of water heater inner tanks. Volumetric electric water heaters are the most common and commonly used water heaters. The steel materials of the inner tank are divided into steel pottery coating, steel galvanized, stainless steel and so on. Many domestic water heater manufacturers use basically the above three types of inner tanks. The steel inner tank is exposed to a hot water environment of about 70 for a long time, and the inner wall will be severely corroded. The corrosion products have a certain impact on the water quality, resulting in the inner wall. The gall bladder wears the notification to waste. Professional foreign water heater manufacturers usually use sacrificial anode and cathodic protection to solve the problem of pinhole corrosion and penetration of the inner tank. This method is quite mature and commercialized. However, some domestic water heater manufacturers know little about the production and application of this anode rod alloy material. Therefore, the technical research of using cathodic protection to effectively control the corrosion of the inner tank wall urgently needs to be popularized. 1. Screening and evaluation of sacrificial anode materials Cathodic protection technology is used for the corrosion protection of the inner tank of electric water heaters, and the sacrificial anode method is usually adopted. The sacrificial anode method is to couple the metal to be protected with an active metal with a more negative potential. Because the two electrodes have different potentials, they form a galvanic cell, thereby generating a cathodic current that plays a role of cathodic protection, which has a higher potential than the protected metal. The negative active metal is the sacrificial anode (usually called magnesium alloy sacrificial anode rod in water heater applications). 1.1 The sacrificial anode materials widely used at present mainly include: zinc, zinc alloy, aluminum alloy, magnesium and magnesium alloy, etc. Among these anodes, magnesium and magnesium alloy anodes have the lowest potential, and have a large drive potential to iron. The open circuit potential is -1.6V to -1.7V, which is especially suitable for use in fresh water with high resistivity. In addition, magnesium is also necessary for the human body and has no toxic side effects to the human body. The disadvantage is that the self-corrosion effect is large, the efficiency is low (only about 50%, due to the hydrogen evolution on the electrode surface, the negative difference effect and the cause of the metal shedding), and the consumption is fast. Despite the shortcomings in the above-mentioned aspects, compared with other sacrificial anode alloys, magnesium alloy is still the preferred material for water heater anodes. The current efficiency of the zinc anode can reach 95%. In the water heater, zinc is usually used as a sacrificial anode in the form of zinc or electro-galvanized. However, the passivation performance of the zinc anode increases with the temperature, and the zinc electrode potential shifts positively, zinc-iron Electricity

Specification

Dimension and Weight

metal@vip.163.com

China Hunan High Broad New Material was founded in 2006, focus on the business in advanced new material and service. Including: design, installation, material , engineering, maintenance and technical support.

Our sales office located in Changsha, Hunan province, plant located in Hunan,Shanxi, Henan,Guizhou province.Our business scope including : Cathodic protection products for fresh water and marine anti-corrosion products such as magnesium anodes,Aluminum anodes ,Zinc anodes etc.;Master alloy for aerospace ; Aluminum alloy , Magnesium investment castings industry; Magnesium alloy profile :Extrusion/hot rolled billet, plates,bars etc .for various civil & military industry,such as grade AZ31B,AM80,WE43,ZK60 etc.; high wear-resistance & hardness ceramic products for sandblasting nozzle & bulletproof plate for armor vest, armor vehicle.

Along with strong economic development  in China, we expand our business very well, Product capacity is over 5000mt per year.Turnover reach to USD20,000,000.00 per year.

Our Products are widely accepted and recognized by clients worldwide including Europe, North America, East Asia, Middle east etc..

Our R&D department have strong technical design capacity. We closely cooperated with colleges and universities, supply the service for various companies in China and overseas.

Believe we can be your long term and reliable supplier .