Solenoid Based Two Directional Double Channel Turnstile Full Height
Indoor And Outdoor
Quick Descirption of High Security Gates
Full height turnstile is a kind of access control equipment
designed for placeswith high class security requirements. It is
easy to combine IC access control, ID access control, code reader,
fingerprint, face recognition and other identification devices. It
realizes the intelligent and efficient management of passage. The
turnstile is the best choice for access control of modern building.
Full height turnstile series are fully applicable to a high traffic
flow places like school,factory, park, and other places.
Specification of Full-Height Gate
| Material | SUS 304 stainless steel |
| Input power | AC220V/110V, 50/60HZ |
| Motor | Solenoid |
| Work temperature | -20℃ ~ 70℃ |
| Rated power | Single core 50W,double core 100W |
| Work environment | indoor / outdoor available |
| Passage speed | 20-35person/min |
| Communication Interface | RS485, open/close signal(relay), dry contact |
| MTBF | 5 million cycles |
| Pass Width | 600mm |
| Passage direction | one-directional/Bi-directional |
| IP level | IP65 |
Arm rotation angle | 90degree and 120degree |
Fire /Emergency Alarm | Yes |
| Work voltage | DC 24V |
| Applications | Stadium, factory, amusement park, government security, public
transportation |
Features of bi-directional turnstile
More security
DOOR’s full-height barrier combines maximum security with a rugged
and swift design to prevent climb-over attempts and tailgating in
unmanned areas.
Available in a variety of styles
DOOR's full height turnstile is available as an indoor or outdoor
turnstile, a single or double unit, and with your choice of
motorised or mechanical side gates in a number of finishes,
including stainless steel and galvanised paint in RAL colours.
Turnstiles System Operation Principle
1) Turn on the power, 2 seconds later; the system enters into work
mode; the arm can’t be turned.
2) After swipe legal card or code and fingerprint, Access control
device send opening signal to control board.
3) The control board receives open signal, control indicator to
green,6 solenoid open , The arm of rotation can be pushed to 90
degree or 120 degree.
4) After the passenger push rod and then rotation turn to 90 or 120
degree, the position sensor send close signal to control board, the
solenoid lock immediately.
5) Full turnstiles will lock after 5 seconds if the passenger swipe
card but do not pass.
FAQ about turnstile
Q1:When access board send open sigal,arm move reverse and indicator
show reverse?
Reasons:open signal reverse connection
Solotion:exchange SW1 GND and SW2 GND terminal of board.
Q2: Indicator is not working?
Reasons:1. wires loose 2.indicator or board damage
Solution:1.Check connect wire of indicator 2.Repalce indicator or
board.
Q3: How to achieve free for one way ?
1.Remove one of square solenoid
Q4: Arm can not push when swipe card and indicator show green?
Solution: 1.Check 24V GND output for square solenoid 2.Replace new
board or solenoid
Q5: Passing two or three people after swipe card at a time.
Reasons: 1. The Positon sensor didn’t be touched by the right screw
cap when the turn plate rotating. (Or didn’t receive the effective
signal even touched)
2.The square solenoid does not stretch smoothly.
3.Control baord damageSolution: 1.Move the position senor inward
,Check connect wires to board
2.Adjust square solenoid or replace new one.
3. Changing the square solenoid.
4. Replace a new board
Packing of Single Channel Full Height Turnstile
| G.W. (KG/plywood case) | N.W. (KG) | MEASUREMENT (CBM) |
| 395 | 345 | 2150*1700*1350mm |
