15m High Altitude Install 12VDC Input Remote Control Motio Snesor
Detection area of DC sensor:
This figure indicates the maximum distance at the highest mounting
height with 100% sensitivity.
Typical installation height 8-15m
| Mounting height | Max.15m/49.2ft (ceiling mounted) |
| Detection range | Max.ø14m/45.92ft (ceiling mounted) |
| Detection angle | 30°-150°(without the glass) |
| Motion detection | 0.5~1.5m/s |
Features of ON/OFF Sensor:
1. 15m high installation with 51*24.4*14mm
2. Display remote to set parameters
3. Input 12VDC / 0-10V dimming
4. 10/30min hold time and longest 30min stand-by period to make
sure light will keep ON before people walk away from the space,
especialy the big warehouse;
5. Maximize 14m diameter detection area to make it suitable for big
warehouse and gym;
6. With daylight function, light keep OFF even people walked into
the detection area during the daytime;
7.Operating current<25mA
8.12VDC input, no limitation for the loading capacity
Technical date of DC sensor:
| Operating voltage | 120-277VAC,50Hz/60Hz |
| Operating current | ≤25mA |
| Stand-by power | ≤0.5W |
| Output | DIM/0-10V |
| Detection area | 25%/50%/75%/100% |
| Hold time | 5s/30s/1min/3min/5min/10min/20min/30min |
| Daylight threshold | 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable |
| Stand-by period | 0s/10s/30s/1min/5min/10min/30min/+∞ |
| Stand-by dimming level | 10%/20%/30%/50% |
| Microwave frequency | 5.8GHz±75MHz |
| Microwave power | <0.3mW |
| Operating temperature | -20°C~+60°C |
Factory Default Setting: Detection area 100%/ Hold time 5s/
Daylight threshold Disable/Stand-by
period 0s/Stand-by dimming level 10%.
Parameters of DC sensor:
Mechanical structure | | 1.Connector:3 PIN connector
2.Installation hole:Two mounting holes for easy fixation in the
lamps
3.Daylight sensor:Strain the light intensity, convert the light
signal into electrical signal, control the switch of the lamp
4.Antenna module:Detect motion signals of objects |
| Dimensions(mm) | | 1.The shell size is 51*24.4*14mm 2.The wire length is 270mm |
| Wiring diagram | | 1.The wire color would be Red 12v,Black GND,Green DIM 2.The output is 0-10V dimming |
Application:
1. Automatically ON/OFF function:
| With sufficient daylight,even when motion detected,light remains
OFF. |
| With insufficient daylight,when motion detected, light ON. |
| After the last detection and the present hold time elapsed, light
OFF. |
2. No daylight function
When the daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off after
stand-by period.
Applications: Dim places such as Basement Parking, Underpass.
| When motion is detected, the sensor will switch on the light to
100% brighteness. |
| After people leave the detection area, light remains 100%
brightness within hold time. |
| After the last detection and the present hold time elapsed, light
OFF. |
3. Function Demo - Dimmable control/Corridor function
| With sufficient daylight,even when motion detected,light remains
OFF. |
| With insufficient daylight,when motion detected, light ON. |
| After last detection, the light will be dimmed down to the stand-by dimming level (10%,20%,30% or 50%) after holdtime. |
| After the stand-by period, light OFF. |
Installation Method of DC Sensor:
1. Microwave sensor can be installed in any lamp except the one
with full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
4. The detection surface of the sensor module shall be installed
facing the detection area.
5. Should be kept away from the driver to avoid interference
generation and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to
avoid short circuit.
HD015VCRH.pdf
